Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Fixing A Broken Ignition Switch

Scotty Kilmer, mechanic for the last 46 years, shows how you can fix a broken ignition switch in your vehicle. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&feature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.


 


More Videos...


Fixing A Honda That Died On The Road
Scotty Kilmer, mechanic for the last 46 years, shows how he fixed a Honda that died on the road and was towed to him. Learn how to replace a bad distributor assembly. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





How To Remove Stuck Nuts And Bolts
Scotty Kilmer, mechanic for the last 46 years, shows how you can remove those stuck nuts and bolts when working on your car. Don't blow your head gasket trying to remove them, just use a little heat as this video shows. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Rewiring Electrical Power Through The Ignition Switch
Scotty Kilmer, mechanic for the last 46 years, shows how you can rewire electrical power in your car to devices that have lost power. Using the ignition switch power wire and a toggle switch, many expensive devices can be rewired to bypass insanely expensive computer driven systems. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Finding The Source Of Electrical Shorts In Your Car
Scotty Kilmer, mechanic for the last 46 years, shows how you can find where shorts exist in your car. Using a simple broadcasting tool, you can trace down shorts in just minutes. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





no start / crank : troubleshoot the ignition switch
Starter replacement here : http://youtu.be/N0lK3eUflh0 If the starter doesn't crank when you turn the ignition key, the possible causes are: - the ignition switch - the start relay (if present) - the continuity of the electrical circuit - the starter itself One of the method in car troubleshooting is to proceed by elimination. This video shows how to test the ignition switch in order to eliminate this cause of failure. Troubleshooting breakdown car starter engine doesn't start doesn't crank nothing happens starter motor Auto, automobile, car, vehicle maintenance tools parts accessories engine mechanics do-it-yourself diy tutorial tuto This video does not constitute or replace a real specialized technical manual, and was only made ​​for convenience and educational purposes. "TutoBuild Eng" makes no warranties of any kind and accepts no liability. "TutoBuild Eng" cannot be held responsible for any damage caused to devices or persons using information contained in this video. The use of the information contained in this video is at your own risk.





Honda Accord Ignition Switch Replacement
A fastener by fastener tutorial for testing, removing, and installing an ignition switch on a Honda Accord. I cover how to cause an intermittent switch to act up, test it for continuity to verify it's faulty, and how to remove the cylinder assembly from the vehicle so the electrical switch can be removed. Then I cover the 1990s to 2000s Honda ignition switch recalls and the special part numbers that go with them and reinstallation of the cylinder assembly to the vehicle. The shear bolt diameter and thread pitch is M8 X 1.25. Ignition Switch Recall Info: Honda TSB Number 02-031 Vehicles affected: 1997 Accord (L4), 1998-1999 Accord (L4 and V6), 1998-2000 Civic, 1997-1999 CRV, 1997-2000 Odyssey, and 1997-1999 Prelude. Link to the recall PDF with installation diagrams: http://www.driveaccord.net/PDF/ignition_switch.pdf Intro and outro music Welcome To The Show by Kevin Macleod (Incompetech.com). Due to factors beyond the control of Bushougoma, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bushougoma assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bushougoma recommends safe practices when working with the tools or equipment seen or implied in this video. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Bushougoma.





My Car Wont Turn Over - How To Test The Starter / NSS / Ignition Switch
http://www.bleepinjeep.com/ - All the best Off-road videos of YouTube : Please hit us up on FB - http://www.facebook.com/BleepinJeep In this video I'll show you how to do a simple test on your starter that will tell you if the starter is getting power or not. If it is getting voltage then this diagnosis this will tell you that your Neutral Safety Switch (NSS) and Ignition Switch are working and that the issue is in your starter. If your test reveals no power to the Starter then you'll know that the Starter is probably good and the problem is in the NSS or Ignition Switch. Then I'll show you how to jump start the starter to start your car incase there is something wrong with the ignition switch. *Disclaimer - This product is meant for entertainment purposes only. Your mileage may vary. Do not try this at home. Void where prohibited. Some assembly required. For off-road use only. Slippery when wet. Batteries not included. Do not use while operating a motor vehicle, heavy equipment, cherokee, wrangler, or any jeep vehicle. May be too intense for some viewers and children under 30 years of age. Please remain seated until the ride has come to a complete stop. Studies have shown viewing these videos causes increased cancer risks in laboratory test people. I am not a professional, I have no training, I'm not even particularly good at horse whispering. Don't believe everything that you know. Please keep your hands in the vehicle at all times. Do not tap on glass. Do not eat anything that has been on the floor for more than 3 days. Keep your hands to yourself. Not to be taken internally. Reproduction strictly prohibited. Driver does not carry cash. Objects in jeep mirrors may be farther than they appear.*





Ignition Lock Cylinder Removal
Ignition Lock Cylinder Removal 00-02 Saturn S-series





94-97 Honda Accord Ignition Switch Replacement Part 1
A fastener by fastener tutorial for testing and removing a faulty ignition switch on a Honda Accord. In part one I cover how to cause an intermittent switch to act up, test it for continuity to verify it's faulty, and how to remove the cylinder assembly from the vehicle so the electrical switch can be removed. In part two I cover the 1990s to 2000s Honda ignition switch recalls and the special part numbers that go with them and reinstallation of the cylinder assembly to the vehicle. The shear bolt diameter and thread pitch is M8 X 1.25. Part 2: http://www.youtube.com/watch?v=h0pYfY31h5Y Link to the recall PDF with installation diagrams: http://www.driveaccord.net/PDF/ignition_switch.pdf Intro and outro music Welcome To The Show by Kevin Macleod (Incompetech.com). Due to factors beyond the control of Bushougoma, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bushougoma assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bushougoma recommends safe practices when working with the tools or equipment seen or implied in this video. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Bushougoma.





How to diagnose a bad starter, ignition, neutral safety switch!
The re are 3 wires or electrodes on all starters. One is the large bolt that is attached to the main positive battery cable. One is the small wire that is sometimes purple that is attached to the ignition switch "key". And one is just a copper wire or electrode that supplies a ground/power to the starter from the solenoid.





How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Avoiding Common Auto Repair Mistakes
Scotty Kilmer, mechanic for the last 46 years, shows how to avoid some common auto repair mistakes.And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Fixing Broken Power Windows On Your Car
Scotty Kilmer, mechanic for the last 46 years, shows how you can fix that broken power window on your car. Nothing is needed but simple hand tools and the will to save money doing it yourself. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Does Lacquer Thinner Clean Catalytic Converters? -EricTheCarGuy
Link to Scotty Kilmer's Video: http://www.youtube.com/watch?v=5icTmYItwiE After watching Scotty's video I was curious if it would actually work. Since we know from my video on diagnosing catalytic converters that the catalytic converters in my Subaru were bad, I though it was a perfect opportunity to try out this theory. I used about 1 quart of lacquer thinner to about 7 gallons of gas. I drove a total of 200 miles and tested the converters. The testing showed a very slight improvement but nothing that I would call significant. It was worth a try. I can say that I did not notice any issues with drivability during or after the test. It may not have fixed the problem, but it didn't seem to cause any other problems either. I feel the check engine light that came on was just a coincidence and not the result of putting lacquer thinner in the gas tank. Here's some useful links for you. Diagnosing a P0420: http://www.youtube.com/watch?v=9VZ5K8n5jj0 Discussion about this video: http://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/47854- does-lacquer-thinner-clean-catalytic-converters#77372 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Dumb Things NOT To Do To Your Car
Scotty Kilmer, mechanic for the last 47 years, shows some of the dumb things he's seen people do to their cars. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

1975 MG B GT V8: 9.620 @ 137.370
Perry Stephenson, Engine: Rover 3.9 litre modified, Supercharger: GMC 4/71 0 Tires: 28 x 9 x 14 ET Drag


1975 MG B GT V8: 9.810 @ 138.620
Perry Stephenson, Engine: Rover V8 4.9 litre, Supercharger: GMC 4/71 Turbos: none


1975 MG B GT V8: 9.960 @ 136.130
Perry Stephenson, Engine: Rover V8, Supercharger: GMC 4/71


1975 MG B GT V8: 10.290 @ 131.390
Perry Stephenson, Engine: Rover V8 4.6 litre (280 ci), Supercharger: GM 4/71 Tires: MT ET Drag 28x9x15


1975 MG B GT V8: 10.410 @ 129.550
perry stephenson,


1975 MG B GT V8: 10.660 @ 126.510
Perry Stephenson, Engine: 4.6 litre, Supercharger: no Turbos: no Tires: Toyo prox + M/T ET Drags


1986 BMW 325e : 10.970 @ 135.690
Jacob Edwards , Engine: Toyota 2JZizzle, Supercharger: naw Turbos: Precision Billet 6266 T4 .81 Tires: 245/50/16 Nitto street tires


1998 Pontiac Sunfire GT garret gt42 Turbo: 10.997 @ 133.720
Paul Rocha, Engine: 2.4L, Turbos: garret gt42 Tires: 26/10/15


1975 MG B GT V8: 11.560 @ 117.810
Perry Stephenson, Engine: Rover 4.6, 0 0 Tires: Toyo and MT Streets


1986 BMW 325e s: 11.967 @ 113.530
Jim Rando, Engine: 1998 M3 S52 3.2 L, Supercharger: N/A Turbos: N/A Tires: 225/50 15 Hoosier drag radials


1975 MG B GT V8: 12.080 @ 114.200
Perry Stephenson, Engine: 4.6 litre Rover V8, 0 0 Tires: Dunlop and BFG Drag Radials


2003 Pontiac Sunfire se/s s/c stage 3: 13.114 @ 105.260
patfire, Engine: 2.2 ecotec, Supercharger: eaton m45 Tires: 205/55/16


1971 MG B V6: 13.342 @ 104.195
Terry, Engine: 4.3 chevy bored 4.5, 2 bolts main, Tires: Sumitomo HRT200 185-70-14


2000 Pontiac Sunfire GT Supercharger: 13.900 @ 103.530
john miller, Engine: 2.4 twin cam, Supercharger: gm eaton M45 Turbos: none Tires: good year


2002 Pontiac Sunfire GT: 13.928 @ 102.350
stephan(sun), Engine: 2.2 ECOtec, Tires: 27/8/15 slicks


2009 Lexus GS350 : 14.110 @ 99.610
NA, Engine: V6: 303HP,


2007 Lexus GS350 : 14.119 @ 99.660
tt061880,


1996 Pontiac Sunfire GT: 14.200 @ 97.000
Aasyranth, Turbos: custom T4/T04E turbosystem


2003 Pontiac Sunfire Coupe: 14.760 @ 91.670
Jonathan, Engine: 2.2 Ecotec, Tires: P195/65/15


1986 BMW 325e : 14.850 @ 92.700
JT, Engine: 2.7i, Tires: 195/65/14


 


©2014 DragTimes - Disclaimer - Contact Us