Blue Ox Base Plate Installation - 2010 Chevy HHR - etrailer.com

http://www.etrailer.com/tv-blue-ox-base-plate-install-chevy-hhr.aspx Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2010 Chevy HHR we are going to install part number BX1692. The first thing we need to do is go ahead and open up the hood and we are going to remove two 7 millimeter bolts from the front fascia near the headlight housings. The next thing we do is go down to the fender well. We are looking at the driver side. And we are going to remove three fasteners, two plastic rivets and another 7 millimeter screw. Alright, now there are two plastic rivets underneath the vehicle that we need to remove also. We are just forward of our front tire and we are looking at the passenger side. We are done with the passenger side. Let us move over to the driver side. This model also has a fog light installed on the bumper fascia as well. So we are going to have to remove this fastener here so we can reach up and disconnect the wiring for those. 1:12

More Videos...


Edge Racing Evolution CTS Performance Chip Review - etrailer.com
http://www.etrailer.com/tv-review-edge-evolution-programmer-EP85700.aspx Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2002 Chevrolet Silverado 2500 we are going to show you how to use an Edge Evolution CTS programmer. Before you start using the Edge Evolution CTS, we strongly recommend that you read through the user guide a couple of times to become familiar with the Evolution and what it can do. In our previous video, we showed you how to install the Edge Evolution CTS. At the end of the video, the programmer requests the activation key. The owner of the truck went on Edges website, registered the unit and acquired the activation key so that we can unlock the Evolution CTS and set it up. Once you have activated the Evolution, you are going to head to the main menu where you are going to start putting some information about your vehicle into the system. We have a Chevrolet Silverado 2500 so we will Chevy. And it is now prompting us to make sure that our key is in the on position. Do not start the motor. Just turn the key until your accessories come on. With our key on, we are verifying that we are indeed in a GM/Chevrolet truck. Select yes. The Evolution is going to go through some processes here of checking the computer and reading some information so it knows how to tune. 1:10





Trailer Hitch Installation - 2011 Chevy Equinox - etrailer.com
http://www.etrailer.com/tv-hitch-install-2011-chevy-equinox.aspx Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today we will be installing Hidden Hitch part number 87572, comparable to Draw-Tite part number 75681, on a 2011 Chevy Equinox. A couple of key measurements to think about when ing your accessories such as a drawbar, a bike rack or a cargo carrier is the measurement from your center pin hole to the very most edge of your bumper is 4-1/2 inches. From the top of the receiver opening to the ground is 12 inches. Now we are going to proceed with our installation. Our first step will be the removal of a fascia piece so that our hitch, when installed, will not be hitting our lower bumper and fascia. There are several snaps holding the fascia in place. Sometimes a screw driver will be necessary to pry them loose. 1:00





Trailer Wiring Harness Installation - 2010 Kia Sedona - etrailer.com
http://www.etrailer.com/tv-Wiring-install-2010-Kia-Sedona.aspx Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2010 Kia Sedona we are going to install part number 118410 from Tow Ready. OK, this is our T-one wiring harness. Now the first thing we need to do is open up that back hatch. We will start off on the driver side. It looks like there are three screws we need to remove. When you pull the light off, you have to pull it in the general direction away from the vehicle at an angle, like this. Alright, we will go ahead and disconnect the taillight right here. Push down that center tab and it comes apart. Set that aside for now. We will go over to the passenger side and do the same thing. Next we will go ahead and take the 4-pole itself and just it into the cavity between the body and the bumper cover and pull it out the bottom. Then we will take the one half of the T-connector with the red and green wires and that through as well. 1:00





Thule AeroBlade Crossroad Roof Rack Installation - 2011 Chevrolet HHR - etrailer.com
http://www.etrailer.com/multi-product.aspx?pc1=THARB43&pc2=TH450R&vehicleid =20111026255&hhmake=Chevrolet&hhmodel=HHR&hunter=roof&roofkit=1B,3,4,NB,7,8 ,9&manuf=TRS Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Follow