Repair cvt VT25-E/VT20-E, Saturn, Opel.
Demonstrated inside the repair of variator VT25-E/VT20-E (continuous
variable transmission: CVT), mounted on car Saturn Vue 2,2l 2002-2005 and
Ion Quad Coupe 2,2l 2003-2004. Also installed on the car Opel Signum
2004-2007 and the Opel Vectra C 2004-2007.
Ремонт вариатора VT25-E/VT20-E. Saturn Vue, OPEL.
Want to race a Saturn?
My good friend was out one night having a hard time looking for a race in
his 2006 Saturn Ion Red Line. Someone in a turbo Eclipse finally decided to race against him.
And yes, the guy in the turbo Eclipse
was giving it all he had, even with a head start.
This video was produced by SLEEPYDUB for AuDUBahn Motorsports Gruppe.
Created by Jacob Edwards. www.AuDUBahn.com
2007 Saturn ION Starting Problems
Since we drove the car off the lot it would periodically not start on
demand only to start some time later (usually 15 minutes or so). Because
this problem cannot be replicated on demand we have filmed an instance when
the car would not start.
Cutting White Wire on Saturn Ion to Fix Starting Issue
UPDATE 3/21/2014: My car is still working fine. I still have not had a
problem with it starting since I posted this video 5 years ago. Still on
the same battery. Thanks for all the comments!
This is me showing how I cut the passlock wire on my car. My car would not
start on damp, cold mornings, often taking 30 - 40 minutes to get it to
start. After reading several forums I found users who were doing this to
"fix" the problem. I thought I would tape this for anyone who was thinking
of doing the same but doesn't know anything about cars. Like me. :)
Note: I owe thanks to meron for the post at this link
http://townhall-talk.edmunds.com/direct/view/.f1137a7/83 it is where I
first heard about this solution.
Update 10.6.2012: I added a switch, I believe it was this one
http://www.radioshack.com/product/index.jsp?productId=2062533 I installed
it with it in the off position, started the car, switched it to On while
the car was running and the service engine light went away. Car started
fine after that. I just shut it off again as it was cold one morning this
week and I had trouble getting the car started. Once I got it running,
turned it off and haven't had trouble starting it since. YMMV
2003 Saturn Ion that won't start in cold weather
Documenting my attempt to use a fix I found on the internet to resolve an
issue that plagues 2003-2004 Saturn Ions. The models in this year can have
difficulty starting in cold weather. At first it was pretty sporadic for
me but this year it was almost constant.
In the video I replace the ignition switch which actually ended up
resolving my problem. I guess there is a lubricant in this switch that
SHOULDN'T harden in cold weather but the ones that shipped in the cars of
these years do. Total cost $29.99 and about 30 minutes of time.
The specific symptoms you will see with this issue are (usually in cold
weather) you will try to start the car and it might crank a couple times
but then die. When you try to start it again you will hear a short fire
but then it stops. This is because the security system has kicked in and
shut off fuel to the vehicle for 10 minutes. After you wait 10 minutes you
can try to start it again. This cycle can happen multiple times (at its
worst I would have to go almost an hour of doing this).
Once you replace the part you may have to reset the security (passlock).
This is done by turning the key to start (but it won't) and then leaving it
in the run position until the lock light in the dash quits blinking (about
10 minutes). You then do this again (again waiting 10 minutes) and finally
a THIRD time (waiting another 10 minutes). After the third attempt you
turn the key to OFF and wait 30 seconds (this waiting is important I am
told!). It should then fire up.
Be sure to watch this on the Web if you can as I have a lot of in-video
comments to help!
Ion Redline Exhaust
BadMab Shorty Header, 3 inch MFlow high flow cat Down Pipe, 3 inch
resonated magnaflow Cat Back.
Saturn Ion ignition switch replace part 2
I have 6 videos
Part - 1 - removing the steering column bezel
Part - 2 - Replacing the ignition switch and putting the steering column
bezel back on
Part - 3 - First step of the Pass Lock reset
Part - 4 - second step of the Pass Lock reset
Part - 5 - third step of the Pass Lock reset
Part - 6 - Success.