svt focus vs sentra spec V
1/8 th of a mile i hope svt-f owners will like this :
both cars are a little bit tuned ..nothing major ..on my svt : no catalyzer
stainless steel pipe with magnaflow Exhaust , cold air intake , 65 mm throttle ,
computer sct excalibrator , aluminium crank pulleys
sentra said his engine was forged ..he was straight pipe like me with the
c/a intake and more that i dont remember
filmed at st-eustache - quebec - Canada (near montreal)
2011 Camaro RS vs 2003 Nissan Sentra SER Spec V
*Typo: Camaro RS is
-2003 Nissan Sentra SER Spec V (with oil burning issues and a low
compression cylinder lol): 3" AEM short ram intake, cheap no-brand replica
Ebay 4-1 header, muffler, tires with low tread, and no passengers
-2011 Camaro RS (2LS):
6-speed automatic but driver was in manual mode using tap-shifters, bone
stock, and one passenger
Video filmed on a closed course.
Nissan Sentra 2015 - Exterior and Interior
Government & Seized Auto Auctions. Cars 95% Off! -
Subscribe For More Videos! - http://bit.ly/PerpetuumSubcribe
Pinterest - http://www.pinterest.com/perpetuumcars/
Google+ - https://plus.google.com/u/0/b/102521076027967518254 (c)
Everything belongs to their respective owners!
Any copyright issues?
Please send me a message or post comment below.
I can remove it asap or add your copyright/source.
No copyright infringement intended.
All photos belongs to the rightful owners.
For entertainment purpose only!
600 WHP Turbo Nissan Sentra Spec V
Here is the video at the race track on 20 psi:
Here is on low Boost 15 psi:
And the new power at 27psi:
Z-Fever builds VQ35 turbo Sentra Spec-V, 1st start.MOV
This is a fully built VQ35 engine we swapped into an 06 Nissan Sentra
Spec-V. It has CP pistons, Eagle rods, ARP head and main studs, Cosworth
Metal head gaskets, and JWT cams adn springs....
We also custom fabricated this single turbonetics turbo kit. It uses a 60-1 ball-bearing turbo, 800cc PE injectors, a turbonetics raptor BOV, and turbonetics 50mm external wastegate.
We also made the full 3" stainless Exhaust system, polished the timing covers, made
all the engine mounts in a CNC, and tuned the ECU using Osiris.
This is the absolute 1st start up video..... From here it will need to go
onto teh Dyno for
For more information about what we do here at Z-Fever please check out our
website at zfever.com .... You can also go to VQ35swap.com for more info on
our VQ35 swap packages.
Dont forget to like us on www.facebook.com/zfever or you can call us
sirectly at 813-877-7600
thanks for checking out our video.
Sentra Se-R Spec V vs 350Z
Tucson 2012 Import Face off 1/29
This 350z was fully bolted. He told me he had header, intake, Exhaust, pulley, and plenum spacer. He ran a
14.7. his top end KILLS!
I ran a 15.0 on this run and im also using slicks. I was competing in all
My spec v
custom 3" Vibrant Exhaust with Quiet
jwt balance shaft removal
walbro fuel pump
NGK Iridium spark plugs
Ported and Polished Intake Manifold and Throttle Body
Aem F I/C
N2MB WOT box
Dual window switch (butterflies open at 4500)
Aem wideband o2 sensor
Tein SS Coilovers
front Eibach sway bar
rear Eibach sway bar
4 pt. tanabe bar
20mm Wheel Spacers
My Sentra Spec V vs. Prelude (all 4 runs)
My Spec V with nismo intake, stillen Exhaust, and energy suspension motor mounts. My
friends Prelude has Intake, Exhaust,
under pulleys, NGK wires, NGK sparkplug wires, and Jdm tranny (shorter
gears) Great race no trash talk and my friend said i was the first to get
him off the line. It was about 95 degrees out so we will race again when
its much cooler. On the 1st run i wasnt paying attention to the light.