CUSTOM CHEVY NOVA with a HUGE V8. DougCameraman

Classic Chevy Nova with a huge engine cruisin' by at Cruisin' Grand. Subscribe, comment, like & share. Here's this video's link to share .. http://Youtu.be/L96EX61gLJE

More Videos...


Bad BLOWN Nova Drag Car Cold Start 14psi 650+hp
My Pro Street Nova. Has been featured in magazines and has pulled record Dyno numbers for sbc w/steel 882 heads. Titanium valves, roller rockers, full port job, etc. etc. Check out my channel to see more! https://www.facebook.com/tinman2kustoms https://twitter.com/Tinman2Kustoms





1970 Chevrolet Nova 1000HP
Over 1000HP Check out my facebook page! "Like" & Share! https://www.facebook.com/MikeAnthonyAutosportsyoutubecomnorthsiderollers





INSANE Chevy Nova 360 SPIN!!! - Pucker Factor 10.0
Another WILD ride from the WYCO Racing 'Operation Octane' No Prep Event on the Pit Road at Kansas Speedway. The driver of the orange Nova was sawing the wheel hard but finally decided the grass looked better than the wall, and he saves it!





Ken Jones - 69 Chevy Nova 383 - Launch Street Radials 2
Before the nova was painted (black) and restored 383 Stroker: (633hp/577tq @ fly) 1969 Original SS 350 Block - 4 bolt main (3970010 cast numbers) - block had been resin filled for strength Eagle - 4340 Forged 3.75" crank (this is an actual 383 specific crank, not a 400 crank milled down to a 383) -Knife Edged and Lightened Eagle H-Beam 4340 Forged Rods (6" rods) JE 4340 Forged Pancake Pistons (full floating pins and Nitrous reliefs) (11:1 Compression = Runs just fine on 91 octane pump gas, but loves 103 octane) - Pistons were Ceramic Coated for Nitrous but nitours has never been run on it. (been wanting to but never got around to it) 64cc Edelbrock Performer RPM Heads (Aluminum) -Fully ported and port matched to the intake and Exhaust -Valves Sizes increased from 2.02/1.60 to 2.08/1.60 -Rev Kit / K-Motion Springs -Comp Full Roller Rockers Holley Strip Dominator Intake Manifold -Port-matched to heads Holley 830cfm Mechanical Double Pumper Carb (re-jetted with jet kit included) -fuel pump is mounted right next to the Fuel Cell and is fully plummed with dash 8 AN fittings and dash 8 steel braded fuel lines. All Transmission lines are done the same way as well Iski Cam - Solid Roller Cam - .602/.602 lift 300/300 duration with 1.6' rockers = .642 final lift Ignition: MSD 6AL Box with changeable rev limiter chips MSD Distributor Griffin 2 - 1 inch core radiator Black Magic Electric Fan Remote Trans Cooler with onboard electric fan Entire assembly has been blueprinted, matched and balanced to each corresponding part. Exhaust: Hooker Supercomp Headers Dual 3" Tubes Dual 2 Chamber 50 Series Flowmasters (this setup sucks... get the Borla XR1s instead) Drivetrain: TH 350 Manual Valvebody Race Transmission Beefed up Driveshaft by Whittier Driveline 3.73 gears with a mini spool in video, then switched to 4.56 minispool, but that was too much, now its got a 12bolt posi 4.11 Heat treated axles Rear-End was a 10-bolt (sucks..) now 12 bolt. Multi leaf springs and lift bars 4000 Stall with anti balloon plates for Nitrous




Follow