An Oldsmobile Alero can't do that! No turbo, no S/C, no spray and my Alero runs 14.96 at E-town. It runs 1/2 second faster at Atco. An Alero can be fast, if you know what you are doing. The guys in the tower are having fun with me too! This happens when you've been racing at the same track for a few years
2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style
bearings done without using a shop press. Specific for Mazda Protege, but
many of the techniques will apply to vehicles with pres-in-style wheel
It's a good idea to try to use the bearing-press-kit the way it was
intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The
bolt supplied with the press-kit is not very strong...it with probably
shear off the head. Try to give the bearin a few hits with a sledge hammer
as seen in the vid..it will get the bearing moving. Then you can use the
press-kit, and it should finish pressing out the bearing.
Pressing in the bearing with the kit should be no problem.
Oldsmobile Factory Tour in 1951 - General Motors Documentary
Singers Lucille and Johnny, whose radio show is sponsored by Oldsmobile,
are invited to visit the Oldsmobile factory to see why the cars are
superior to other manufacturers. While touring the plant, Johnny becomes
concerned that another visitor is a Martian spy dedicated to subverting
Camaro racing Alero
Good 1/4mile race between a Camaro and a supercharged alero!
For more videos and to see the Hottest and Fastest rides in the south go to
Jay Leno gets his 1000bhp Oldsmobile added to Gran Turismo 6
The American chat show host has had his crazy 1966 Oldsmobile Toronado
1000bhp custom car digitised by the makers of Gran Turismo 6, the new video
game for Sony Playstation. Here Jay drives the real and virtual versions
and speaks to the game designer Kazunori Yamauchi about this one-off car.
We also get a look at Mercedes' AMG Vision Gran Turismo concept car, which
was designed specifically for the game.
Read more about GT6 at www.driving.co.uk
Replacing an Accord Wheel Bearing - EricTheCarGuy
Replacing an Accord Wheel Bearing
Ok, here it is finally. A few of you have requested this procedure so here
it is. As I said in the video I normally use a different method of
removing the hub from the bearing assembly by using a slide hammer. I also
normally use a press to reinstall the hub into the new bearing instead of
hitting it with a hammer. Life is not perfect and we sometimes have to
improvise as I did here. I know a few of you will ask about the size
fasteners that I used to hammer the bearing out, I used hardened (8.8)
10x1.25 bolts to do the job. I also promised links to the other videos
that relate to this one so here they are.
"Oops, Axle Ball Joint Replacement"
and also "How to Replace Honda Captive Rotors"
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Thanks again to all that have subscribed and left such great comments on my
videos and my channel, you are the best, I mean it.
You know the line
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Information about Oldsmobile V8 engines
In this video I talk about the "late" Oldsmobile V8 and offer tips on how
to identify them by number.
"Late" in this instance means 1964-1990. Early('49-64) Olds engines are an
entirely different block, etc.
Sometimes my info gets a bit twisted when it stays inside my head for a
while, so a correction is that '77-80 heads are 3A, not 4A. 4A heads are
Also, to clarify and avoid confusion, this...7 A is a 350 head, this...7A
is a later 307 head. You can also tell the difference easily by the ports.
Late 307 and 260 ports are half the size of any other versions.
Trivia: The Olds 403 was used in 1977-79 Pontiac Trans-Am's, but not all of
Of note...the engine in the video is painted the incorrect shade of gold,
which appears to be the Krylon generic gold. The proper shade is slightly
darker and less "glitzy"
How to Change a Wheel Bearing (long and detailed version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
Here are some other similar how to videos (there are a lot more than this):
How to change brake pads:
How to replace drum brakes:
How to change an Alternator:
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.