Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Chevy fuel tank removal

How to drop a fuel tank, and remove and replace the fuel pump assembly to replace a fuel sender, fuel pump or fix DTC (check engine light) P0463 or P0462 in a Chevy Trailblazer (same as Envoy, Bravada, Rainier).


 


More Videos...


Chevrolet Fuel Pump Installation Trick
Fuel pump installation for 1999 up NEW BODY STYLE trucks, vans, and SUV's. This way is MUCH easier... Not sure if this will work with a 6.6 Duramax Diesel MU1228/MU1288 Pump.. Part # ACDELCO MU1613





Fuel Tank Pressure Sensor Quick-Fix
Software Catalog: http://www.autodiagnosticsandpublishing.com/Software_Catalog.html Fuel Tank Pressure Sensor Quick-Fix The 3 wire fuel tank pressure sensor, is connected to the fuel tank by a hose, and to the ECM. The ECM uses this value to run the EVAP monitor. This sensor has no bearing on how the engine runs. Here are the facts about the fuel tank pressure sensor: 1) The fuel tank pressure sensor is a 0 to 5 volt sensor. 2) You should NOT see a stuck on 0 or 5 volt signal value, using a scanner or volt meter. It has to be somewhere in between. 3) If sensor's stuck at 0 volts, then the 5 volt wire is broken. 4) If sensor's stuck at 5 volts, then the ground wire is broken, between the connector and ECM side. 5) You can jump either the sensor ground or 5 volts to signal and it won't hurt the ECM. 6) If you're stuck at either 0 or 5 volts, disconnect the sensor, and suddenly you have voltage at the signal wire, then the wiring is fine. Replace the sensor, or check tank pressure. 7) To test, connect a voltmeter to the signal wire, disconnect tak pressure sensor, jump sensor ground to signal, then also jump sensor 5 volt reference to signal. Do this at the sensor connector. You should see 0 and 5 volts respectively. That proves the ECM and wiring. It also proves that the fuel tank pressure sensor is faulty, replace the sensor. Finally, if your sensor value is stuck somehwere else between 0 and 5 volts, make sure you're not building too much pressure nside the tank due to a faulty fuel cap, or EVAP vent valve. That's it for the Fuel Tank Pressure Sensor Quick-Fix.





2001 Chevrolet Silverado Fuel Pump Replacement
http://www.apdty.com/searchitem.epc?lookfor=MU1613,GF652 In this video we'll replace the fuel pump in a 2001 Silverado. These instructions will be similar for all Chevy and GMC Trucks and full size SUV's from 1999 - 2006. Click the link above to find the exact fuel pump we used in this video.





Suzuki fuel tank dent repair in real time
This metal work is done in front of the camera in real time to stay moving on it. The next step is in real time too in the following link... http://youtu.be/vl02JP8Kf1E SHOP http://www.mountainviewautobody.com/milogonework.html





How To Remove The Fuel Tank
http://www.autozone.com/autozone/parts/Fuel-Pump/_/N-8vcz2 In the third installment of the AutoZone Complete Car Care - Fuel Pump Series, Bruce Bonebrake shows how to remove a fuel tank.





Chevy Blazer \ GMC Jimmy Fuel Pump Replacement - DIY How to Replace a Fuel Pump Part 2
This video is a quick tutorial on how to replace a fuel pump on a GM vehicle. The vehicle in this video is a 2000 Chevy Blazer, but the fuel pump replacement procedure will be the same or similar on many other GMC vehicles including GMC Jimmy and Chevy S10 pickup. This is the second video in the fuel pump replacement set, the first video walks your through removing the fuel tank and the third video will show how to re-install the fuel tank. I will link to the fuel tank removal instruction video and fuel tank installation video at the end of this video.





How To Diagnose A Fuel Pump Failure - EricTheCarGuy
I had the privilege of visiting Airtex, and while I was there I spoke with Shane Neuman about diagnosing a faulty fuel pump. In this video we go over the basic steps of diagnosing a faulty fuel pump. So if your vehicle isn't starting and you suspect a fuel pump problem, here are some steps to follow to confirm your suspicions. Another 'quick' test is to bang on the fuel tank and then try and start the engine. Sometimes this works, just don't bang too hard, you could damage something. Airtex diagnosis webpage: http://www.airtexproducts.com/techresources1.html Here's a link to an article I wrote on diagnosing No Starts that you might also find useful: http://www.ericthecarguy.com/faq/solving-automotive-no-start-problems The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How To Tell If Your Fuel Pump Is Bad
Scotty Kilmer, mechanic for the last 46 years, shows how to find out if your car's fuel pump has gone bad. Some simple tests are all that's needed, and you don't want to guess with a new pump without testing, as some can cost over a thousand dollars to replace. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





GM Fuel Pump Relay Testing
For more on fuel pressure testing, go to my website at www.scannerdanner.com 1999 Chevy Suburban with no fuel pressure. The following is covered in this video: 1. How to test a fuel pump relay in a power distribution box. 2. Power side switched circuit design description and operation. 3. Bias voltage on an output. How and why is it used. 4. Fuel pump power and ground testing. 5. How to manually jump a fuel pump from the fuse box 6. How to measure fuel pump current flow.





03 Trailblazer fuel pump replacement
Replacing the fuel pump in a 2003 Trailblazer. I used the Bosch fuel pump #67415. The number on the pump itself was 15077623, which matched the number on the OEM pump. The correct fuel pump o-ring for my 03 is the AC Delco #G30. When I have more details on what the green o-ring is for, I'll update this with a video response. Thanks for watching and thanks for subscribing!





GMC Jimmy \ Chevy Blazer Fuel Tank Removal -Fuel Pump Replacement Instructions DIY Part 1
This video walks you through removing the fuel tank on a 2000 Chevy Blazer, GMC Jimmy and other GM vehicles. This is the first step in the fuel pump replacement procedure. I'll be posting a video on how to install the fuel pump, as well as how to install the gas tank, when the order comes in. Removing the fuel tank on a Chevy Blazer \ GMC Jimmy is not that bad of a job. I've also posted a close up shot of how to release the quick connectors on the fuel line. The instructions in this video will be the same of similar on several other vehicles. I would not recommend purchasing a cheap fuel pump, stick with AC Delco, Delphi or possibly Bosh. I purchased a Delphi fuel pump on Amazon for $169.99 (free shipping). You can replace your own fuel tank sending unit!





Cutting Fuel Pump Access Panel and Removing Fuel Pump Assembly - 86 Trans AM with 02 Gas Tank
Watch in HD! Been a little while since I had any videos to share! But now I have quite a few to edit and upload so stay tuned! This is some shots of me making my access panel for my fuel pump in my 86 Trans AM. The fuel tank is a 2002 plastic fuel tank. You'll notice with this combination, I dont need to cut the football field sized hole that you need to cut with the 82-92 and 93-98 metal tanks. Its a pretty small opening. I make sure I radius cut the corners to keep the stress points down. I will be making a nice cover to seal this up. I might put it in another video, but most likely Ill do it and comment on it in another video. Im not 100% thrilled with how the nibbler worked. I should have practiced with it a little to get a feel for how it was going to cut. But, it worked. Thanks for watching!





How to Disconnect Common Fuel Line Fittings
This video is about how to disconnect common fuel line fittings. Airtex is committed to providing the most up-to-date, in-depth fuel pump replacement information that professional technicians need to diagnose, repair and install today's complex fuel delivery systems. Airtex is the only U.S. automotive aftermarket manufacturer that designs and builds electrical AND mechanical fuel delivery system components, including modular reservoir assemblies, electric fuel pumps, mechanical fuel pumps and in-tank sender and hanger assemblies, for a full range of car, truck, fleet and specialty vehicles.





How To Replace The Fuel Pump In A Chevy Silverado Or GMC Sierra
In this walkthrough I replace the fuel pump in a 2000 Chevrolet Silverado in which the fuel level sending unit has begun to fail. These steps will work for any 99 and up Silverado or Sierra. I take a shortcut to the conventional approach by lifting the bed of the pickup off of the frame to access the gas tank instead of draining and dropping the gas tank. If you have any questions feel free to post them on the video and I'll do my best to try to help!





Replace Fuel Tank Sending Unit on 2007 Chevy Malibu
This is a step by step instruction on changing the gas or fuel level sending unit on a 2007 Chevy Malibu. Just a note that where I installed the sending unit, it is preferred that you use the connectors supplied with the sender. I used a splice which was pointed out by some viewers is not the best method. I had a problem using the supplied, as they didn't fit properly, but if I spent the time to file them down, that would be the better method. Mine was done Dec 2012, and still going strong, so it seems solid. For wheel bearing replacement, check this out: https://www.youtube.com/watch?v=Cfut3_EK2k8




Which car is faster? Which Car is Faster?





Similar 1/4 mile timeslips to browse:

1964 Chevrolet Chevy 2: 10.610 @ 117.000
, Engine: 355, Tires: firestone


1991 Chevrolet Chevy S10: 11.526 @ 115.370
Jason Miller, Engine: 350, Tires: micky thomson 32-14.5-15


2005 Chevrolet Chevy Corvette C6: 12.557 @ 110.860
James, Engine: LS2, Tires: Stock non Z51 run flats


1955 Chevrolet Chevy : 12.720 @ 109.500
Ken Abbott, Engine: 454 Chevy, Tires: 28.5 Slicks on rear


 


©2014 DragTimes - Disclaimer