Starting 1984 Z28 H.O. Camaro
This was one of the first time i've started this Camaro, since several years of
The idle was too high, and the starter was out.
And the '72 Corvette which lights me (behind me) had problems of lighting !
All is beeing to be restaured since 2005. The rebuilt engine has been
started. It was cracked engine... So a brand new 350 came.
See my others videos of starting engines.
New Spot ManCamaro :
1984 Z28 Camaro Project Car
My dad's 1984 Chevrolet Z28 Camaro.
I no longer plan to restore and use this car as a daily driver. I will be
buying an older pickup truck and will restore it and I will upload videos
of the restoration process of it.
I will restore this car at a later time. Fuel economy plays a big role in
this decision and I really
would like something that already runs and doesn't have 200k miles and that
gets better than 8 to 10 mpg and doesn't have rust holes everywhere. I have
been finding more and more big problems with this car than I first thought
there were and it is cheeper for me to get a more practical and a bit
better on gas. I hope this doesn't dissapoint anyone and I hope you guys
enjoy the videos to come!
Shout out to gearheadAbe
Keep up the good videos!
my 1984 camaro z28 305 h.o 5 speed burnout
My 1984 Camaro small
burnout 3/4 throttle because if i floor it the clutch slips needs a new
one... its a 305 H.O 5 speed 40000 origanal miles ive had it sence it was
ten and am going to keep it and restore it. iv had it 7 years now been a
real good car. last time out before it went in garage for winter and im
gunna put in new clutch
1984 Chevrolet Camaro z/28 Project
This is the edited version of my other video. I must say I despise windows
movie maker, the song always goes out of sync when you're trying to edit.
This 1984 Chevrolet Camaro Z/28 is my first car.
Purchased without a motor I got a great deal. It came with relatively
fresh paint, 85iroc gfx, and almost no rust except for on the LCA's (which
i plan to replace). The body has 118k km's on it as well as the T-5
tranny. The previous owner has bought a 3" mandrel bent stainless header
back Exhaust with a cat delete. it
came with a set of hooker competition headers as well as weld draglites all
around, 215's in the front, 255's in the back.
Since i bought the car in may, '08 I've bought a '69 010 sbc longblock.
tore it all down and rebuilt it to make sure it was done right. (good
thing i did, somehow the previous owner managed to get a seed inbetween the
deck/heads.) So far the engine is rebuilt, bored .060 over with
hypereutectice pistons, a .477 lift cam with 112 LSA, '72 883 heads,
edelbrock rpm air gap intake, holley 650 dp w/ squarebore mech secondaries
and hooker headers. Nothing fancy, but as a student, cars are bloody
expensive. one day i want to built a nice all-aluminum roller 383.
As for the car, nothing much has been done to it yet, all i've done is put
new e-brake cables in. However, once the motors in and running, i'm going
to put my funds into a pile of UMI suspension stuff, such as SFC's, LCA's,
LCARB's, Adj PHB, Wonderbar, Koni Yellows all around, Eibach Pro-kit and
maybe a hurst shifter / shift knob ( i feel it gives the car a more late
60's muscle car look), and maybe some 4th gen seats and audio equipment
(since theres absolutely nothing now).
Anyways, the video's not as good as i was hoping, i was patient with movie
maker for a while, but now eventually i just gave up. would rather do it
1985 IROC Z28 BRAND NEW
Anyone that would like to see what happened to this car after I sold it
should visit www.thirdgen(dot)org. Go to the message boards and do a search
for "4.3 mile IROC-Z". There are informative comments along with videos and
pictures of the car cleaned up and running. All the people that have
commented how much work would be needed to clean it up and get it running
are proved wrong. The car was sold by that owner over a year ago at a Mecum
auction for $27K and has yet to surface again.
Third Gen Camaro Z/28
This is my 1984 Z28 Camaro, currently equipped with a
"H.O." 305, 5 speed, and 3.73 Posi in the rear. Exhaust is custom.
In the process of building a 383 Stroker for it.
AFR 195 heads
Forged Scat crank
Forged Scat 6" connecting rods
Forged pistons (10.5:1)
Victor Jr. Intake
Crane roller rockers
Custom grind LSM roller cam
and a few other odds and ends which I can't remember right now.
Shout out to Thirdgen.org
This site is a must for all your Third gen Camaro / Firebird needs
1984 Z28 Camaro
Im tired of seeing cars with insane amounts of money put into em so this is
about my stock Z28
Chevrolet Camaro Z28 - Test Drive and Hoon of a 3rd Gen
A simple morning drive featuring a 1982 Camaro Z28 with a few mechanical
updates. This car was built to be driven and I do... a lot.
Here's a list of some of the additions:
GM Performance 290 HP 350 c.i. crate engine
Baer T4 Cross drilled and slotted brakes
Flowmaster 3" Exhaust
Spohn tubular control arms and torque arm
Koni adjustable shocks
Flaming River quick ratio steering box and leather wheel
OMP racing seats
6 point mild steel cage
6 Speed manual transmission built by Hanlon Motorsports
...and the seriously sweet Alpine cassette stereo from the 80's!