2012 Dodge Ram 1500 Crew Cab 5.7L HEMI- TRUE DUAL Exhaust! Removed factory Y-Pipe, muffler, resonators, and tips. Installed a 2.25" Inlet x 2.25" Outlet X-Pipe, two Flowmaster Super 10 Stainless Steel 2.5" Inlet x 2.5" Outlet mufflers, straight pipe in place of the resonators, and 4" Polished Stainless Steel Angle Cut Tips. FULLY CUSTOM, and FULLY WELDED! Factory air filter.
Installation of a 6 inch lift from Top Gun Customz on a 2012 Dodge Ram 3500
Like us on Facebook @: https://www.facebook.com/BlinkAutomotive
This is an installation video of a 6" Lift from Top Gun Customz, This is on
a 2012 Dodge Ram 3500.
This video is for entertainment purposes only. Please read all of your
instructions for your specific lift.
Music by: Kevin MacLeod @ INCOMPETECH.com
2012 Ram Hemi 5.7 glasspack exhaust (race at end) HD
My 2012 Ram 1500 ST with 5.7L Hemi v8, K&N cold air intake, stock Exhaust manifolds and headers that Y into 1 pipe
then go into muffler, I cut out the muffler and installed one 18" glasspack
that comes out 1 pipe then Y's again and goes to the factory duals (the
small factory resonators before each tip are still installed or it would be
If you turn it up and listen closely at 2:20 you can hear the "helicopter"
sound you get with after market Exhaust on engines with MDS (multi-displacement
shut-down), the 3 drive offs at 2:50 were normal take off, half throttle
and full throttle.
2013 Ram 1500 5.7 Hemi Straight Pipe
Immediately after purchasing my new Ram, I had the muffler removed and
replaced it with a Y-Pipe. Everything else is still stock, leaving the
resonators and catalytic converters.
Video of powder coated tips:
Video with CAI and Ported TB: https://www.youtube.com/watch?v=Qx6ccllCzuU
AIRAID Intake For Dodge Ram 2009-2012 5.7L Install Video
AIRAID once again proves to be your one-stop source for performance air
intake systems with our MXP Series cold air intake for the 2009, 2010,
2011, 2012 Dodge Ram 1500, 2500! Best of all, this system nets 18
additional horsepower and 22-lb-ft of
The Ram's 5.7L Hemi engine is a proven and well-respected power plant, but
just like any engine it can benefit from cold, clean, and efficient air
charge. AIRAID's new MXP Series intake system includes a new roto-molded
air box that replaces the factory's restrictive design. Blade style
weatherstripping installed on the air box seals against the hood, keeping
hot engine compartment air away from the filter. A new Tri-lobe designed
roto-molded intake tube is also included to further promote airflow. This
system features a massive 1700cfm air filter that is available with either
oiled SynthaFlow® or non-oiled SynthaMax® material. Both filter styles
are washable and reusable. Stainless steel clamps and related hardware make
this one of the highest quality intake systems on the market today.
This system utilizes all of the OE attachment points and installs in
minutes using common hand tools. Like the rest of AIRAID's product line,
this new MXP Series intake system is backed by the company's "No Hassle"
Features include :
• +18 horsepower
• +22 LB/FT Torque Increase
• Tri-lobe Intake Tube
• No Tuning Required
• Easy Bolt-On Installation
P/N # 300-237 (Oiled) :
P/N # 301-237 (NON-Oiled) :
30ft Flamethrower exhaust!
Video shot at frankensteiners ball in Anoka MN, October 20, 2013. Was a
great show, have lots more footage of the show on my channel. Please
subscribe and check out my channel to see more :)