Colorado in a Mud Trench @ Mettowee Off-Road Extreme Park
I try to get through a mud trench at Mettowee Off-Road Extreme Park. I'm
glad I didn't make it through the last part. Looking at what happened to
the lifted F350 with 49" tires, I woulda buried my truck. Who thinks I'll
need a strap?
Mettowee Mud Boggers Club, LLC.
The nation's premier Chevy Colorado and GMC Canyon website and forum.
Big Black at the Colorado City Mud Bog
Here is video of Big Black at the Colorado City Mud Bog. it was held at the
Colorado City Fair Grounds by the 4H club. This is the second pass we
made. the video of the first pass wasn't very good, plus this was a better
run because i started in 3rd and went to 4rth.
Bad ass Colorado
Chevy Colorado, 2005 I5 with4" TOUGH COUNTRY LIFT, 31" DICK CEPEK TIRES
WRAPPED AROUND 17 X 8" GOLIATH RIMS, TWO ROCKFORD FOSGATE 6.5" SPEAKERS IN
FRONT, FOUR R.F. TWEETERS, A 1600 WATT R.F. AMP, PIONEER PREMIER DECK WITH
USB HOOK UP- AUX HOOK UP- AND IPOD HOOK UP IN BACK, SO YOUR IPOD CAN BE IN
YOUR GLOVEBOX. CUSTOM SUB BOX (BELOW BACK SEAT) EQUIPPED WITH TWO PIONEER
10" SUBS, ALL WEATHER RUMMER "HARLEY DAVIDSON" FLOOR MATS, FLOWMASTER ExhaustWITH CHROME TIP, AEM BRUTE FORCE
AIR INTAKE, JET PERFORMANCE CHIP, TWO OFFROAD LIGHTS, CUSTOM GRILL (LINCOLN
STYLE) -I'VE NEVER SEEN SOMEONE ELSE WITH THIS GRILL- TINT, TWO DIAMOND
PLATED MUD GUARDS, DIAMOND PLATED TRUCK BOX, MOUNTED TUBULAR NERF BARS,
FENDER FLARES (THREE INCH I THINK), BED LINER
Chevy vrs Ford 4x4
all new 2007 chevy silverado vrs F150 4x4 triton 5.4 vs vortecmax 6.0 4x4
Get a Little Mud on The Tires
Some mudding in a 2004 Chevy Z71 Colorado 2WD. In Evans (Augusta), Ga.
Powerline trail and logging road mud ruts. Georgia Z71. you can hear some
of our CB chatter in the background. me and all my buddies have them. I'm
pushing a Cobra 29LTD w/ a linear, cobra extension speaker and mic. and a
wilson 1000 antenna.
Trailer Hitch Installation - 2008 Chevrolet Colorado - etrailer.com
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today we are going to install hitch part number 82641 on a 2008 Chevy
Colorado, and this hitch also fits models from 2004 through 2007, as well
as 2004 through 2008 GMC Canyon. On the side of the frame we need to remove
this rear-most bolt that attaches the bumper and bracket to the frame. And
on the bottom, on pre-2008 models there are actually going to be two
logistic holes here. On this 2008 model, there is actually a weld nut with
a bolt into here, which we are actually going to take out, and we will be
using this hole as well. We need to do that on both sides of the frame.
Okay, with the bolts removed out of the frame, we want to go ahead and put
the carriage bolt and block into the frame. And I am going to go through
this hole here. And we actually want to use the fish wire that they
provided. We want to feed it through the hole at the bottom of the frame
and then run it out through the side access hole. Then we want to put the
block on and then wrap the threads of the bolt with the bolt leader here.
This allows us to pull the bolt and the block through the frame. And for
pre-2008 models that have the secondary hole here, we want to do the same
thing as well. But we want to make sure that the blocks do not overlap
inside the framework, and we need to do this on both sides of the frame. I
do want to make mention here that, again, on models before 2008 where you
have both holes and not the weld nut, the block alignment is critical.
Okay, with the hitch loosely installed here on the frame, I am going to go
ahead and put the existing fastener that we took out earlier back into the
frame. Then we are going to go over here to the side of the frame and
install the fastener here. We want to make sure we put the 1/2 inch block
in between the hitch and the frame. And we want to use the 14-mm hardware
that they provided in the installation kit. Now we want to attach all
fasteners on both sides. Now that we have got all the fasteners loosely
installed, the next step is to tighten them down and then torque them to
their specifications. The 1/2 inch fasteners here at the base of the frame
are going to be torqued to 75 foot-pounds and the 14-mm fastener on the
side of the frame gets torqued to 85 foot-pounds. And now that we have got
all the bolts torqued down, the installation is complete. This concludes
the installation of hitch part number 82641 on a 2008 Chevy Colorado.