6550 gmc safari 2001

6550 gmc safari 2001. Regional Wholesale Inc in Haines City, Florida. Excellent Used Cars, Trucks, Vans, and SUVs. Quality cars at an affordable price. Call Buz, 863-419-4847/863-521-1417. Video by Carviddy, Carviddy.com.

More Videos...


2000 GMC SAFARI @ TITAN AUTO SALES
http://www.TitanUsedCars.com/ This 2000 GMC Safari is available from Titan Auto Sales. For details, call us at 708-671-9140. Please post your comments.





2001 FRESH IMPORT CHEVROLET ASTRO DAY VAN GMC SAFARI LUXURY MPV&CAMPER 4WD
JAPAN MOTORS MPV SPECIALIST 95 Leopold Street Highgate 07443322116 Birmingham West Midlands B12 0UD www.japanmpvmotors.co.uk (http://www.youtube.com/upload)





Trailer Hitch Installation - 2001 GMC Safari - etrailer.com
http://www.etrailer.com/tv-hitch-install-2001-gmc-safari.aspx Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2001 GMC Safari Van we are going to be installing Hidden Hitch part number 87516. We are underneath the vehicle and we are taking a look at the driver side frame rail. We are going to point out the mounting locations we are going to be using for our trailer hitch. You can see here at the end of the frame we have got an existing bumper bracket and that is going to be the same on both the driver and passenger sides. We are going to be removing this bumper bracket and the hitch is going to be replacing it. We have got five fasteners holding the bumper bracket in place and all of those need to be removed and they are going to be replaced with new hardware. 00:31 Then moving forward on the frame we have got an existing weld nut here as well. We are going to be using that as our forward most attaching point for our trailer hitch. That is going to be the same on both the driver and passenger sides. The first thing we are going to do is to remove the bumper brackets from both sides of the vehicle. One more thing we need to do before we put the hitch up into position. You can see that the forward fasteners that we are going to be using did not have any bolts in them previously and are pretty dirty and have some road grime and rust built up in them. So it is a good idea to clean those out thoroughly before we attempt to put the hitch up. To do that we are just going use a spray lubricant like a WD-40. Spray that down and you just want to take a wire brush and run it in there a few times. You may need to do this a couple of times. You can do a test fit of the bolt to insure that it is going to go in easily. You want to do that on the both the driver and passenger sides. Once that is completed put the hitch up in position. 01:36 Into each one of the weld nuts we are going to be using the 10 millimeter bolts along with a lock washer and flat washer. Into the two tabs of mounting the hitch to the bumper itself we are going to be using the same 10 millimeter bolts with simply a flat washer on the one side and then on the other side we will be fastening it with a flat washer, lock washer, and nut. Now that we have got all of our bolts in place we want to go back through and torque them down. You want to verify with the directions the specific torque rating for each of the bolts. With all of our bolts torqued down our installation will be complete. Now with our hitch installed we are going to give you a couple of dimensions that will help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 14 inches. From the center of the pin hole to clear the rear edge of the bumper is going to be approximately 6-3/ 4 inches. This will conclude the installation of Hidden Hitch part number 87516 on a 2001 GMC Safari.





How to Change Tie Rods (inner and outer tie rod ends)
How to replace inner and outer tie rods. This video will show you in depth how to change the inner and outer tie rods of your car or truck. You need a special tool, an inner tie rod end tool, to complete the job (this can be rented for free at your local parts store). The job straight forward and anyone with basic tools can do it! Inexpensive tie rods: http://amzn.to/1XckepV Tie rod tool I used: http://amzn.to/1XcjTUf Inexpensive Tie Rod Tool: http://amzn.to/2j7fwYj Torque Wrench I used: http://amzn.to/1XcoPs8 How to check to see if your tie rod is bad: https://www.youtube.com/watch?v=brI2feYiEi8 Tie Rod End Cutaway: https://www.youtube.com/watch?v=3RjhtVse6jE Become a ChrisFix Subscriber→ http://www.youtube.com/subscription_center?add_user=paintballoo7 Instagram→ https://www.instagram.com/chrisfixit Facebook→ https://www.facebook.com/chrisfix8 Website → http://www.ChrisFixed.com My Channel Home Page → https://www.youtube.com/ChrisFix **If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday** Disclaimer: Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.




Follow