Lucimar Honda Civic vs Ortiz RX7 - Match Race Orlando Speed World - FuelTech
This was the first offical race of the brand new 3/4 chassis project from
Lucimar Racing and FuelTech EMS.
Running consistently on the low 7 seconds:
7.12s @ 196MPH (314km/h)
7.18s @ 193MPH (309km/h)
The Honda K24 is equiped with a Precision Promod 94mm turbo and managed by FuelTech FT400 EFI and all
the FuelTech acessories product line: BoostController2, PRO24 Datalogger, WB-o2 Slim
Find more info about FuelTech products at www.fueltechems.com and
How to build a Rotary Bridge Port engine
FullBoost Tech Files, Ep 1 ~ Rebuild
and Bridgeport of a 13B rotary engine @ Mr Parts.
We have started with a stripped down 1984 Mazda RX7 13BT engine, and will
run through the steps involved in bridge porting the engine, then assembly,
to the start up in its new home, a 1972 Mazda 808 (RX3). [
Follow us on social media @
DIY Fuel Injector Cleaning & Repair
This is the end result of a few hours of work and $60 because I didn't have
a 1/4" NPT tap in any of my kits. I could have done this for less-than
$40. The BG products were donated to the cause.
The REASON you want to use 20 PSI is precisely because of how peak-hold
type injectors work. The injector signal sends a 4v spike to open a
peak-hold type injector quickly, then maintains its open condition with
only 1 volt. Really, it's a current thing and there's a longer
explanation, but that's it in a nutshell. When you put the injector in its
operating pressure, it takes more than a AA battery to open it, but you
don't want to sustain that much current with a momentary switch and your
expensive injectors. This isn't in the video because this warning wouldn't
be as clear. Unless you can simulate the injector pulse precisely, don't
try it. 1.5v is enough to open it below its operating pressure. If you
open it and THEN apply pressure, you can flow as much pressure as you can
throw at it.
I don't discourage anyone from getting their injectors professionally
cleaned and balanced, but in my case, I didn't feel that was necessary.
In my first video, I thanked the seller for these injectors and happy to
know I got a great deal on high quality parts. My gratitude is even
greater because I had problems with them. It gave me an opportunity to
help others troubleshoot these kinds of problems when purchasing used
parts. A different idiot might have blamed the seller for peddling crap,
demanding their money back... but that would only be because they didn't
even know what they were looking at.
This particular idiot knows what high quality parts RC injectors are and
how to clean 'em. $250 + $60 still means I saved about $150 on a brand new
set. We all benefit because I bought these and I'm grateful! Let the good
El Freddy / Import DPS
El Freddy Import DPS 7.03 @ 193 MPH New Record 9 / 3 / 11 Latin American
Drag Fest @ Maple Grove Raceway Thanks to www.grs-motorsports.net
Transformers: Fall of Cybertron - Easter Egg
Transformers: Fall of Cybertron - Easter Egg is in Chapter IX behind the
first Teletraan 1 before Megatron goes up to Starscream coronation
http://www.facebook.com/eltrucote Like & Share Thanks
101mm TURBO CTS-V - 1200hp Cadillac!!!
This was probably the NUTTIEST car we encountered at the Pikes Peak Air
Strip Attack - this 1170hp 101mm turbo
equipped Cadillac CTS-V was turning heads everywhere it went. Hop into the
passenger seat as we race down the 1/2 mile raceway at over 180 mph!