www.dhracing.biz dh-racing 2.1 beast crate motor runs 11 sec all motor
Here is our dhr-racing 2.1 beast crate motor customers vinces car running 11,s this car was also runing dhracing ported head dh-racing ported intake and dh-racing billet honda throttle body combo and dh spec ecu chip built by www.dh-racing.com 702-788-1327 for orders only this car won nopi this guy can drive props good job vince your the man
The JET Bicycle - The most dangerous unsafe bike EVER
An old womans bike built for shopping turned into a bomb inspired safety
hazzard. This is the final part in my series on the wonderfull pulse jet
and what an end.The jet will push the bike a little faster but its staying on thats the
challenage as some of the more keen eye'd people will have noticed the side
shaking , yes we could have cured it with better frame better wheels etc
but i like its a shit bike n still is.
Other videos in the series are
Part 1- Making the jet
Part 2- First test
Part 3- Strapped up in van and nearly setting fire to everything
Part 4- Making the jet bicycle
also follow me on twitter https://twitter.com/colin_furze
and my facebook page
For more info on this project and other crazy ones like it visit my website
Contact me either here on youtube or at email@example.com
Music by march to the grave heres the link etc
How an engine works - comprehensive tutorial animation featuring Toyota engine technologies
Animation I created for Toyota that gives an overview of the components of
an engine, how an engine works and some of Toyota's valve, intake and Exhaust technologies. I wrote, directed
and storyboarded the video. It was for training purposes only.
See other videos at:
How to build a TURBOJET ENGINE
HELLO GEEK WEEK
So this is the first in my trilogy of videos about building a turboJET engine from scrap.
This video is me building the jet then tomorrow i'll take you through the
simple maths and it is simple.
enjoy subscribe and see you next video.
Music by march to the grave
The scrapyard is C.towell and they are great for off cuts of stainless etc
PLUS more at
CRX of DEATH!
Disclaimer: This is not my car
the car belongs to my good friend's father. It is a 88 Crx SI. B20/Vtec
The car used to have an Lsvtec setup which the Dyno video is posted in my
video. best time is 12.6@ 109 mph
********attention new times 12.2 @ 111*****
How To Adjust Valves Honda B18C VTEC 4 Cylinder -EricTheCarGuy
Visit me at: http://www.ericthecarguy.com/
Discussion about this video:
B Series Timing Belt Video:
Valve adjustment tool:
Long feeler gauges:
VTEC explanation video: https://www.youtube.com/watch?v=nc800hkqY2M
I think this might just about complete my valve adjustment videos on Honda
engines. There are only a couple more that I can think of that I haven't
covered like the Vigor 5 cylinder engine and the DOHC VTEC found in the NSX
(that will be a fun one trust me) but that's about it. As you can see in
the video this valve adjustment requires a special tool. You don't have to
use the same one that I used in the video but you won't be able to
accomplish this procedure without some sort of special tool. Once again
make sure the engine is cold and it's probably not a bad idea to run back
through them after you go through the first time just to make sure
everything is still in spec, it's strange how one revolution of the crank
shaft can change things. Otherwise good luck.
Music from Apple's Soundtrack program: Bosa Long
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Trailer: Port Our Head? Tom Says Yes!
Come see what knowledge, talent and some
help from our friends can do with a
B16a and pump gas.
6+ hour DVD build video available
www.portflow.com info on head porting:
talk to Tom Fujita, the man.