Loading Up A Big Rig Diesel Dragster
This twin turbo V8 Detroit Diesel
powered dragster was being loaded onto it's trailer after being run at the
2010 Truckin' For Kids Truck Show. I think the cab is a Kenworth.
Badass Diesel Turbo RAT ROD Pickup
It's not fast, it's not pretty, but it's FUN AS HELL... Rollin coal down
the highway towing his camper trailer, it's quite the sight to see! Take a
tour of Troy Gubser's turbo Diesel rat
rod pickup! This thing sure has character, and it's a blast to roll around
Footage from the Nebraska Diesel Show 2014
RUN AWAY Detroit Diesel! 453-T
DD 453-T runs away! rack gets stuck on valve cover. almost lost some
fingers too, it was all i could find. F'ed up new turbo compressor wheel, was only damage
1977 Military M551 Detroit Diesel 6V53T - First Run - Leid Diesel - 11-26-2010
This is a video of my 1977 General Motors/Detroit Diesel 6V53T engine
It operates on a 2 - Cycle engine design dating back to 1938
The engine is 318 cubic Inches (53 cubic inches per cylinder)
~335 horsepower -
with N70 Injectors and the TV8104 turbo
This engine was pulled from an M551 Sheridan Tank.
This was my first big engine rebuild.
Alot of time, energy and money went into this project. I am pretty happy
with the results. I made mistakes, I learned alot, and I made a lot of new
It is a project most people my age do not take on. That being said, I think
I did a pretty good job so far.
History on this engine:
I completely disassembled this engine after finding out that the engine had
stripped crankcase gears. It took three thorough cleanings to remove all of
the dirt/grime/loose metal and rust from the inside of the engine. Once
clean I attempted to rebuild the engine myself. I was nearly finished when
disaster struck. Two of the oil suppression rings had snapped off the 2R
piston. This little problem resulted in the fourth full engine cleaning.
This time, I wrapped every piece in plastic wrap, to prevent any
dirt/dust/debris from interfering with the engine rebuild.
I brought every piece up to the nearest Detroit Diesel 2 - cycle
specialist. (Leid Diesel in Newville, Pennsylvania) When the owner,
Timothy, said that the liners had about 200,000 miles of wear on them, I
decided to have all of the pistons/liner/rings replaced. For a tank engine
to have that kind of wear, the previous owners clearly ran it too hard and
for far too long.
It was funny looking at their expressions' when I dropped off individually
sealed bags of pieces. That was a first for them, but every engine
re-builder knows that dirt is the enemy, so every precaution needs to be
taken to ensure clean serviceable parts.
During initial dis-assembly, I noticed that some parts just weren't adding
The engine had turbo pistons and
naturally aspirated liners, mismatching camshafts, naturally aspirated
heads with four different types of valves, a natural blower on a turbo block, and so forth.
I made sure to fix all of the irregularities, and in the process I
converted the military engine into a truck engine. For the most part, the
engine is a silver engine, with silver heads/cams, and it will have a
silver turbo coming shortly.
I swapped out the mismatching 7 and V7 cams for matching low lift-low
velocity camshafts (V7L)
Both cylinder heads were replaced with rebuilt silver 6V53 heads (One cast
in 2001, the other in 2002)
The original 16 plate oil coolers were replaced with two 18 plate coolers
All of the liners/rings were replaced. One piston was replaced, and the
other 5 were polished up.
The crankcase gears were replaced, as were all of the bearings and gaskets.
Finally, the military aluminum SAE#3 flywheel housing was swapped out for a
cast iron SAE#2 flywheel housing, so I can mount a big manual transmission
Every piece of this engine was cleaned and inspected by myself, and later
inspected by the folks at Leid Diesel
This project took a year to get to this point. This project would not have
been possible without continued support from my family, Grigg Mullen, Jim
Clarke, Andrew Leamer, Daniel Renovetz, Jason Hughes, Anthony Sgroi, and
the folks at Leid Diesel Service (Timothy, Harold, Phillip, Ervin, Jeremy,
Stay tuned for updated videos,
Thanks for watching,
You can see the entirety of the rebuild on 4BTSWAPS:
453T Detroit Diesel Ford Pickup
4-53T Detroit Diesel Ford F350 Dually.First start after fixing fuel leaks.
V7L low lift cam
Fuller 6406 Trans
D70 3.54 gears
V12 Detriot Diesel 525HP
Setting the engine up and breaking it in.Remember this engine is just being
started after a rebuild so that's why it's smoking from the assembly lube
and the rack will be set-up to stop the hunting etc etc. Then the oil is
changed and the engine painted. These engine's go into Euclid mining rock
trucks,and they were in many other equipment/vehicles.The engine has
rebuild heads,turbo's, blower, water
pump,all internal parts and the air compressor All done in the great north