Change Headlights or Remove Headlight Assembly on Trailblazer
This video shows how to change headlight bulbs or remove the headlight
assembly by removing the grill. Some users may find it easier to reach
behind the headlight, depending on the side, and remove the bulb that way.
The grill can be tricky to remove and can be broken if special attention is
not paid to the clips which hold it in place.
I apologize because I am unable to edit the video and return it to this
page, thus I have tried to include some of the comments which are helpful
in this description.
Works on 2002 - 2006 Chevrolet Trailblazer, shown on 2004.
GrimmSpeed™ Subaru License Plate Relocation Kit Installation
* Most adjustability available on the market!
* Mounts in OEM tow hook location
(No cutting or drilling required)
* Simple stainless steel allen key hardware
* Will not block flow to your FMIC and can be adjusted to not block fog
(Adjustments available for maximum air flow)
* Indestructible Black Zinc coated 12L14 shaft
(This will not bind and break off in your tow hook hole like cheap
License plates are a necessary evil on the front of our cars, but you can
save your front bumper from looking boring or blocking flow to your FMIC
with the GrimmSpeed License Plate Relocation Kit. Utilizing our unique
Infinite-Adjust design allows for virtually any mounting position and
angular adjustment so you can mount it where you want it! Our simple design
mounts in the OEM tow hook location for maximum support while providing you
with the largest range of adjustment available on the market. Laser cut and
powder coated 5052 Aluminum, this bracket will hold your plate confidently
in place while looking sharp and light. Each tow hook adapter is custom
designed and CNC machined from 12L14 and then treated with black zinc to
Re-defining style, it's what you can expect from GrimmSpeed™
CHEVY TRAILBLAZER 2002 HEADLIGHT BULB REPLACEMENT
I am not a mechanic, but can do very basic repair.
Replace the headlight bulbs in my 2002 trailblazer and if not careful you
might end up with a broken grill.
This is very easy to do, you need to know there are 10 snap locking tabs
holding your trailblazer grill, 2 under each headlight and 6 right front
center grill (4 top & 2 bottom).
and 2 more locks hold your headlight.
It's a short film and it's the first time I edit one also.
Like I said I am not a mechanic nor a film maker, hope this helps you or
hope you can find better.
You Know My Steez
For more information you can go to WWW.PROJECTSTEEZ.COM
This is the latest short of my car I put together to showcase it. Its a
2008 Mitsubishi Evo X with the following mods. The clip was produced and
editing by me.
* AEM Intake
* K&N Oil Filter
* Buschur Upper Intercooler Pipe
* Rexpeed CF Radiator Cover, CF Inake Inlet, CF Engine Cover
* AEM Tru Boost
* Agency Power Downpipe
* Agency Power Dual Exhaust
* Agency Power Intercooler
* Road Race Engineering Tune
* Carbon Fiber Bumper Cover
* Carbon Fiber B-Pillar
* Carbon Fiber Antenna
* Do-Luck trunk
* JDM Fog Light Delete
* Altec Motorized License Plate
Wheels and Suspension:
* Forgestar F14 wheels in Gold 19x10 all around
* Falken FK 452 tires
* BC racing coilovers
* Eclipse AVN726e Headunit
* Scoshe Dash Kit
* Agency Power Carbon Fiber Gauge Pod
* AEM Voltage Gauge
* AEM A/F Gauge
* Carbon Fiber Vibrant Shift Knob
* Mode Racing Short Shifter
1/2 mile racing for top speed in the middle of no where in Coalinga, CA on
October 5-6th, 2013