How To Change a Timing Belt Dodge Intrepid 95-97 Part 1 1AAuto.com
1A Auto shows you how to install, change or replace a cracked, snapped, cut or timing belt. Another common reason to change this is if your car has high mileage and is recommended to be changed by your vehicle manufacturer. This video is applicable to the 95, 96, and 97 Dodge Intrepid models.
How to Install Replace Headlight and Bulb Chevy Malibu 97-03 1AAuto.com
1A Auto shows you how to repair, install, fix, change or replace the
broken, damaged, cracked, faded, cloudy, or chipped headlights on your
vehicle. This video is applicable to the Chevy Malibu, years 97, 98, 99,
00, 01, 02, and 03.
1AAuto.com How To Bleed Drum Brakes
1A Auto shows you the procedure for bleeding drum brakes and includes some
tips that will help you complete the task easily and safely. They show you
what happens when no brake fluid comes out and how to unplug a bleeder.
WARNING: Before you buy a Dodge Intrepid 2.7L or Chrysler Concorde 2.7L
1998-2004 Dodge Intrepids & Chrysler Concordes that are equipped with the
2.7 v6 are sensitive to on-time maintenance. Most cars can handle neglect
and abuse much better than the 2.7 v6. MY BEST ADVICE IS TO AVOID THE DODGE
INTREPID/CHRYSLER CONCORDE/CHRYSLER SEBRING/DODGE STRATUS WITH THE 2.7 V6,
unless you have proof of a water pump & timing chain replacement as well as
use of synthetic oil. Without proof of the water pump change and synthetic
oil use, a 2.7 v6 is running on borrowed time.
I made this video to help current or potential Intrepid buyers. In no way
am I defending them because I personally would not let anyone I know drive
one of these 2.7 equipped cars. IF YOU MUST BUY AN INTREPID OR OTHER LH
CAR, THE 3.2 or 3.5 V6 IS WHAT I'D CONSIDER AN ABSOLUTE NECESSITY FOR THEIR
Peugeot 406 Timing Belt Change
Changing a timing belt on a peugeot 406 2.0 HDi 110 DW10ATED
The car has around 122,000 miles and apparently it had a new belt put on at
79,000 miles but there was no receipts so to be sure i changed it.
It is quite an involved job, a lot of things to do and it needs to be done
right otherwise it can wreck the cars engine.
I would recommend reading the Haynes Manual and this, and reading them a
number of times to fully understand what is involved:
The tensioning procedure i did not show completely in the video as its hard
to show on camera and its best if you read the guide to see how its done.
I also replaced the water pump as its good to do when your in there, the
crankshaft oil seal was leaking hence all the oil/sludge in the area,
engine degreaser was used liberally to clean up the area and timing belt
covers before putting the new belt on.
Videos that will also help:
Crankshaft pulley replacement:
Filling coolant and bleeding the cooling system on a HDi:
I hope this video helps to show what is involved with a timing belt change
on a 2.0 HDi DW10ATED engine, but i strongly recommend that you read the
manual and the other guides.
I only intend for this video to help and condense the timing belt
replacement procedure, any suggestions on how to do things differently are
How To Solve An Engine Overheat Condition - EricTheCarGuy
How To Solve An Engine Overheat Condition - EricTheCarGuy
I actually had fun putting this one together for you since the car I was
working on didn't cooperate it made it so I could show you real world
problems as they happened, very cool. I think this one is pretty self
explanatory so I will save a long explanation. In case you missed the link
to the "Bleeding a Cooling System" here is a link for you
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Astra Turbo (z20let) Timing Belt Install - Part 1 of 2
Warning. Serious damage may occur to your engine if the timing marks are
not correctly positioned. Only undertake if you have the tools and the
confidence for such a job.
Please source other advice and guides to compliment this video.
Time lapse installation video of removing the z20let timing belt and
replacing the water pump. Installing the new timing belt is in part 2.
How to Remove an Old Timing Belt and Tensioner
In the third installment of the AutoZone Complete Car Care - Timing Belt
Series, Bruce Bonebrake shows how remove an old belt and tensioner with
step by step instructions.
Get everything you need to do the job right at http://www.autozone.com
2002 Dodge Intrepid - Headlight Restoration Part 1 of 2
Watch Part Two: http://www.youtube.com/watch?v=u4TlHDG74Bo
Part 1 of 2: Inexpensive DIY headlight restoration on my 2002 Dodge
Intrepid. Using wet sanding and some PlastX plastic polish from Meguiare's,
I spent around $8 for all the materials. The bonus, I still have TONS of
the sand paper and plastix polish left over. Enough to do a fleet of cars!
3M Wet Sandpaper (300, 800 and 2000 grit): Any Wal-Mart/Autozone or
automotive parts store with a Paint section
Maguiare's PlastX Clear Plastic Cleaner and Polish: