Supersprint Exhaust Interior of BMW 330i
Some clips for anyone who want to hear what a Supersprint Exhaust sounds like in normal driving situations
with some play mixed in too!
To be honest there is a minor bit of drone at low RPMs under load. Once a
downshift is done to put RPMs around 3,000 under load (uphill) then the
slight drone disappears.
ZHP with borla exhaust and headers
This is my 2005 330i ZHP with ebay header's borla catback, afe intake, and
shark software. Just a few runs and crappy open diff drift attempts.
2004 BMW 330ci muffler delete
Here I have my 04 BMW 330ci with a muffler delete done locally, by a
muffler shop I trusted, and replaced with two straight pipes. It is a cold
start and it sounds a little gargly to begin with, but tones down later on.
It's a cheap thing to do if you're looking for a deeper inline 6 sound.
BEST of BMW M5 V10!! BURNOUT, DRIFTS, REVS!!
This video is a compilation of the best BMW M5 E60 V10 Exhaust sounds I have filmed in the last few
years. In this video you can hear the start up sound from the V10 engine,
some very loud revs, burnouts, drifts and mindblowing accelerations! Just
listen to the V10 engine sound, it's amazing! Maybe the best V10 ever made?
Don't forget to Like & Share this video!
1st Channel: http://www.YouTube.com/GUMBAL
2nd Channel: http://www.YouTube.com/GUMBALTV
3rd Channel: http://www.YouTube.com/CarChannelClassic
Thanks you for watching my videos. All feedback on my videos are
appreciated! Don't forget to like the video and subscribe to my channel.
More videos coming up!
BMW Crash Compilation #1
Rate, Share and Subscribe !
Like us on Facebook: http://www.facebook.com/topcrashes
Car Crash Community: http://gplus.to/carcrashes
Follow on Twitter: https://twitter.com/CarCrashWorld
2009 BMW 335i gets Injen Intake & Remus Exhaust
The combination of this dual filter Injen Intake and Remus Exhaust gives this already good lucking 3 series
a physical Boost for a great price.
Colder air running to the engine and less back pressure in the Exhaust is a great way to modify your BMW.
The Remus Sport and Race Exhaust
System features a straight through muffler, reducing backpressure to
provide Dyno proven
gains in horsepower and torque.
Besides an increase in power, this Injen 335i intake you will get better
gas mileage and a deeper tone out of your engine. Aside from the new sound,
this intake will fit perfectly, install easily and release the true power
of those turbos, allowing them more
cooler air then ever before.
For more information on this Remus Exhaust, CLICK HERE: http://goo.gl/sxs7Ap
For more information on this Injen Intake, CLICK HERE: http://goo.gl/1uB3Ik
For more information on these Forgestar's, CLICK HERE: http://goo.gl/50MCiT
Music by: Bad$ista - After All - Growllective -
1721 E. Lambert Road Unit C
La Habra, CA 90631
Most Competitive Prices Online, Large Inventory, Fast Shipping!
How to install a performance free-flow exhaust on a BMW or MINI
"Like" us on Facebook - http://www.facebook.com/BavarianAutosport
"Follow" us on Twitter - http://www.twitter.com/BavAuto
"Subscribe" to us on YouTube - http://www.youtube.com/BavarianAuto
Visit our online store - http://www.bavauto.com/
All of the items shown in these videos are available in our online store at
http://www.bavauto.com/. Need additional tech help? Please visit our tech
blog for thousands of Tech and DIY BMW and MINI articles at:
Installing a performance free-flow muffler or Exhaust system on your BMW or MINI is a task
that most DIYers should be able to complete in a couple hours to half a
day. Most systems are a direct bolt-on to replace the original parts or a
simple cut-in, where the pipe is cut and the new system slips over the cut
end of the pipe. The new systems hang from the original mounting points
and center into the rear valance opening in the same manner as the original
Since the installation of a full bolt-on system is as straight forward as
simply removing the old system and installing the new system in exactly the
same manner, in this DIY we will show you a typical cut-in system
installation. The only specialized tool that you will need is a pipe
cutter, such as the one that we offer.
Follow along as we install a Scorpion Free-Flow muffler set on a 2007 335i.
Then, listen to the before and after sound clips. Of the 100% stainless
steel systems that we offer, the Scorpion system is our quietest Free-Flow
system (on most models). For a bit more "European" sound, choose the Remus
systems. For those who wish to have the most aggressive Exhaust sounds (and performance), we suggest the
MagnaFlow and the Billy-Boat systems. Remember, all of these systems are
100% stainless steel.
• Scorpion Free-Flow Mufflers for BMW 335i
• Wurth Exhaust Assembly Paste
• New rubber Exhaust hangers, as
• MechanicAll penetrant and lubricant spray
• Exhaust tubing cutter
• SafeGrip Gloves
• 10mm through 15mm 3/8" drive socket and ratchet set with various
• 10mm through 15mm combination wrench set
• Assorted flat-blade screwdrivers and pry-bars.
NOTE: We suggest that you work with a helper to support the muffler
assemblies during set-up and installation.
1) Safely and properly raise the rear of the vehicle. Drive-on ramps can
be used for this procedure, as well as a floor-jack and jack-stands.
NOTE: This DIY is performed on an E90 (06-12) 335i model. This model has
two separate mufflers with two inlet pipes and a cross-over pipe between
the mufflers. In order to lower these units, mark and cut both inlet pipes
and lower as a complete unit. On this vehicle, we separated the two
mufflers at the cross-over pipe due to our performing a live DIY for an
audience and then a second DIY for our video. In separating the mufflers,
we could perform these two full DIYs on one car.
2) Raise and support the new muffler assembly, below the original muffler.
Align the hanging points with the original hanging points. Mark the Exhaust pipe in a location that will
allow the original piping to be inserted into the new muffler's piping by
about 2". Remember, it is better to have to cut a second time to shorten
the pipe, rather than be too short on the first cut.
3) Position the pipe cutter around the pipe, at the marked location.
Tighten the tool and roll the tool as far clockwise and counter-clockwise
as clearance allows. Keep working the tool until the pipe is cut (similar
to cutting copper plumbing pipe with a tubing cutter).
4) Support the muffler and disconnect the forward and rear hangers. Unbolt
the forward hanger bracket from the chassis. Unbolt the rear hanger from
5) Lower the original muffler.
6) Note that the new Muffler has welded on hanger pins for both the front
and the rear hangers.
7) We're sorry, but the description can not be any longer (youtube
requirement). Watch the video and see our tech blog for the full DIY steps
NOTE: For this vehicle, and others with separate left and right mufflers,
install and align both mufflers at the same time. Do not fully tighten the
clamps until you are satisfied that both sides are hanging symmetrically.
All products noted in this video can be purchased in our online store,
http://www.bavauto.com/, 24 hours a day, 7 days a week. You are also
welcome to e-mail us at email@example.com or call into our headquarters and
speak to our knowledgeable advisors at (800) 535-2002 (Mon.-Thurs. 8AM to
9PM EST, Fri. 8AM to 7PM EST, and Sat. 9AM to 4PM EST).