New 2011 Honda Accord Crosstour for sale at Honda Cars of Bellevue...an Omaha Honda Dealer

Test drive the new 2011 Honda Accord Crosstour for sale at Honda Cars of Bellevue http://www.hondacarsofbellevue.com, your exclusive Honda dealer for Bellevue, Nebraska providing superior Honda service to the greater Omaha and Council Bluffs, Iowa metro areas.

More Videos...


2011 Honda Accord Crosstour
Call 1-800-488-4333 or visit http://www.carmichaelhonda.com to test drive this vehicle today. We are also the #1 Parts and Accessory dealer in the nation! Go to http://www.handa.com for a complete list of products. Our dealership is located at 6151 Auburn Boulevard, Citrus Heights, CA 95621.





2011 Honda Accord Crosstour Review - SanTan Honda Superstore
Take a look at the new 2011 Honda Accord Crosstour inside and out with sales associate, Jeff Gunning. For more information, visit https://santanhonda.com or call (480) 285-2800





Replacing Honda Front Struts - EricTheCarGuy
Replacing Honda Front Struts - EricTheCarGuy After posting the last video on replacing struts I thought I would post this one next. I shot this along with the rest of the Accord front end work that I did last fall. A couple of things are different, the most obvious is that the springs are a much smaller diameter so you really need to be careful when you work with these since the spring compressor doesn't have as much to grab hold of. Second, when you install the struts back on the car care must be taken to get the notch on the strut lined up with the wishbone, if you don't do this the upper wishbone bolt will not go in since it has to fit in a groove on the back of the strut. For the second time I've shown you that I tighten the lower wishbone bolt with the car off of the ground, the fact is I shouldn't do this since I'm told it may ruin the bushing that goes through the lower control arm. I believe this to be possible but I have not experienced any problems doing it this way. For me it just seems like a pain in the butt to try and reach around the tire after I've put the wheel back on. But for those of you that like to point out my faults here is my excuse for not doing it the "right" way. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Be safe and stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Honda No Start? POSSIBLE Main Relay - EricTheCarGuy
Honda No Start? POSSIBLE Main Relay - EricTheCarGuy http://www.ericthecarguy.com/default.aspx Here is a GREAT website article about soldering these I strongly suggest you check this out before doing this repair. http://techauto.awardspace.com/mainrelay.html The first of the "Quick Tips". I think I'm going to throw one of these in from time to time to keep things lively. So if you have a Honda or Acura that is not starting DUE TO LOSS OF FUEL PRESSURE this is a good place to start. You may be able to repair the main relay normally found under the dash on the drivers side. If this helps great remember me fondly and pass my name along because I just saved you at the very least about $80, at the most $200. I will be upgrading my website very soon, in fact I will post a video when it is up. Cool new things on the horizon for ETCG and YOU the viewer. So if you want take a look at the old site because it's days are numbered. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Till next time Be Safe and Stay Dirty. Oh yea, and have fun too. ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.




Follow