Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

BMW E46 323i 0-100

BMW E46 323i 0-100 Acceleration


 


More Videos...


BMW 320D Drift
Drift, 20.6 '10 @ Rübenplatz Frauenkirchen





Top 10 BMW Accidents [ Drift FAILS, Burnout FAILS, Crashes ]
WEBSITE »» http://highspeedmania.net FACEBOOK »» http://facebook.com/HighSpeedMania.net TWITTER »» https://twitter.com/HighSpeedMania INSTAGRAM »» http://instagram.com/highspeedmania_net#





2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style bearings done without using a shop press. Specific for Mazda Protege, but many of the techniques will apply to vehicles with pres-in-style wheel bearings. It's a good idea to try to use the bearing-press-kit the way it was intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The bolt supplied with the press-kit is not very strong...it with probably shear off the head. Try to give the bearin a few hits with a sledge hammer as seen in the vid..it will get the bearing moving. Then you can use the press-kit, and it should finish pressing out the bearing. Pressing in the bearing with the kit should be no problem.





Part 2: Installing shocks, struts and springs on a BMW 3 series 99 thru 05 (E46)
BLOG ARTICLE: http://blog.bavauto.com/14307 "Like" us on Facebook - http://www.facebook.com/BavarianAutosport "Follow" us on Twitter - http://www.twitter.com/BavAuto "Subscribe" to us on YouTube - http://www.youtube.com/BavarianAuto Visit our online store - http://www.bavauto.com/ All of the items shown in these videos are available in our online store at http://www.bavauto.com/. Need additional tech help? Please visit our tech blog for thousands of Tech and DIY BMW and MINI articles at: http://blog.bavauto.com/ --- In Part-2 of this two part series, we will replace the rear shock and spring. See Part- for the front shock/spring/strut replacement. The Bentley repair manuals will cover standard shock and spring replacement for the various BMW and MINI models. This DIY will assume that the DIYer has the applicable Bentley manual for additional reference as well as fastener torque values. Note that we will be installing the Bilstein PSS-10 coil-over kit. However, the procedures would be the same for any common shock/strut replacement (including installing sport springs, if desired). PARTS USED: • New shocks/struts (Bilstein, Koni, Sachs, etc.) • New sport or stock replacement springs, if desired (BMW, BavAuto, Eibach, etc.) • New Shock install kits (compression bumpers, dust shields, spring pads, etc.) • New upper strut and shock mounts • New strut & shock mount gaskets (as required) • Rear shock mount reinforcing plates TOOLS USED: • Bentley Repair Manual • BavAuto Non-Marring pry bar set • 13mm through 18mm ½"drive socket & ratchet set with various extensions • 4mm through 8mm Allen keys or bits (for ratchet use) • 13mm through 18mm combination wrench set • Assorted flat and Phillips screwdrivers PROCEDURE: REAR (applies directly to the E46 3-series, but the E36 3-series uses the same steps and procedures): 1) Safely raise the rear of car, with suspension hanging. 2) Remove the wheels. 3) Place a jack under the lower shock mount eye or the wheel hub assembly. Slightly raise the suspension (just enough to remove the downward tension on the shock). 4) Remove the lower shock mount bolt. 5) Lower the jack and allow the suspension to hang free. 6) Remove the trunk side trim panel to access the upper shock mount. 7) Remove the two 13mm nuts from the upper shock mount, at the top of the shock tower. 8) Lower the shock out of the vehicle. 9) Assemble the new shock with new compression bumper, dust tube and upper mount. Be sure to re-use the large lower and upper washers for the upper mount. These washers must cup away from the mount. lower washer cups downward and upper washer cups upward. 10) If the spring is being replaced, it can be removed BEFORE re-installing the shock. Have a helper pull downward on the wheel hub assembly and pull the spring out from between the chassis and the upper control arm. 11) Using new upper and lower spring pads, install the new spring in the same manner as the original was removed. Install the new spring pads, then install the spring. 12) Install the new shock. Place a new shock mount gasket on the shock mount and insert the assembly up into the shock tower. If installing a shock mount reinforcement plate, place the plate over the two shock mount studs, on top of the shock tower, before installing the two nuts. Install the two nuts. Install the trunk trim panel. 13) Install the lower shock mount bolt. Be sure to install the washer on the bolt before installing the bolt. Use the jack to raise the suspension assembly to align the lower shock mount with the hub mounting point, so the bolt can be inserted and threaded. Tighten the bolt. 14) Repeat for the other side. -------- All products noted in this video can be purchased in our online store, http://www.bavauto.com/, 24 hours a day, 7 days a week. You are also welcome to e-mail us at info@bavauto.com or call into our headquarters and speak to our knowledgeable advisors at (800) 535-2002 (Mon.-Thurs. 8AM to 9PM EST, Fri. 8AM to 7PM EST, and Sat. 9AM to 4PM EST).





Top 10 BMW Fails Compilation 2013
Top 10 BMW Fails Compilation 2013 SUPPORT THE ORIGINAL VIDEOS: Fail compilation Video -BMW Drift Fail https://www.youtube.com/watch?v=f6taF5W9vPA Female, BMW and snow - a terrible combination https://www.youtube.com/watch?v=cWWwzov2b2c Idiot with a BMW https://www.youtube.com/watch?v=YDaHA39EwhQ Besoffener Idiot - BMW Syndikat Asphaltfieber 2011 https://www.youtube.com/watch?v=QXDeN66mGcs BMW Clutch Fail! https://www.youtube.com/watch?v=87HzYTPfi2M Bmw M6 Fail https://www.youtube.com/watch?v=87HzYTPfi2M BMW X5 crash at parking https://www.youtube.com/watch?v=3KZRa3sYD-I Fail drift on BMW E30 https://www.youtube.com/watch?v=KaB7DRBTy74 BMW drift failed auto crash 2012 https://www.youtube.com/watch?v=UhhiyWShYNQ BMW 740i FAIL https://www.youtube.com/watch?v=JwsI3_7q4JM bmw s1000rr , bmw 2013, bmw grip, bmw x6 BMW Drift Fail, Idiots with BMW, BMW Clutch FAIL, BMW CRASH, BMW BURNOUT, BMW COMPILATION, FUNNY BMW FAILS, PARKING CRASH, BMW M6, BMW X5, BMW E30, BMW 740i, BMW IN WATER





2005 BMW E46 3-Series Control Arm Replacement
Click here for products featured in this video: http://www.apdty.com/searchitem.epc?lookfor=631020,631031,016912 In this video we'll show you how to replace the control arms and bushings in a BMW E46. This job is also similar to other cars in the 3-series lineup, including the E36.





MMPower BMW E30 325i (EstorilBlue) Project ᴴᴰ
MMPower BMW E30 325i Individual (EstorilBlue) Project Modified List: BBS RS1 Silver Front 8x16" Rear 10x16" Wheels, Maxis MA-Z1 Front & Rear 215/40/16 Tires, Bilshtein Hardness Adjustable Shock Absorbers, Eibach Federn 50mm Lowering SportLine Springs, BMW GmbH M Tech II Body Kit, BMW GmbH Recaro Seats, Wösner 2.8 Stroker Kit, SuperSprint Centre Pipe, SuperSprint (E30 M3 EVO) End Pipe Exhaust, Hella Black Line HeadLight, Startech Blackline Back Light, CAUTION Video Requires Watching High Quality Music System. ©2011 Music By Nazif ©2011 MMPower Project http://mmpowergarage.com/projed.asp?id=24 More Photo & Information For http://mmpowergarage.com/ Galeri / BMW





Wheel Bearing Replacement with Basic Hand Tools
TWITTER: https://twitter.com/CarsNToys FACEBOOK: https://www.facebook.com/pages/Carsntoys/118041931705993 PINTEREST: http://www.pinterest.com/carsnt/boards/ Front wheel bearing replacement on a 2002 Buick LeSabre with basic hand tools. Please note, this vehicle has the bearing built into the hub. Some vehicles may have a taper rolling bearing (usually older vehicles have this setup) or some vehicles may need the bearing to be pressed out of the hub. In this case, the hub & bearing is all one unit. Don't forget to wear safety glasses. Please note: This video is being performed by an experienced tech. Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles. Such as, use safety glasses, jack stands, no loose clothing, etc. No guarantee or warranty is implied. Use the information in this video at your own risk.





Audi A4 3.0TDI quattro vs BMW 335d xDrive (F30)
Beschleunigungsduell zwischen einem Audi A4 Avant quattro S-Line und einem BMW 3er Sports Line. Der BMW hat 70PS mehr wegen des zusätzlichen turbos, aber hat kein Sportfahrwerk. Außerdem die schlechteren Reifen, die Automatik schaltet etwas langsamer und xDrive ist nicht ganz so ausgereicht wie quattro. Hat der Audi trotzdem eine Chance?





Wheel Bearing Removal with Harbor Freight Universal Tool BMW 3 Series Rear Front
I spent about $150 on tools. These tools can be used for any bearings I may need to do in the future. I bought the tools at Harbor Freight.





BMW E30 Turbo 1192HP @ 2.0bar
Time Attack between race driver Mika Salo and owner of the car. Show's concept is that tuners bring their cars to the show and race driver tests it and gives feedback. Owner says it has M5 engine but if it's 2.5, which engine it could possibly be?? Likely it's a mistake. Subtitles are not finished yet. This is not my production!!!





Origin. Bavaria - a Movie about my BMW E46
a Movie about my BMW E46





How to Change a Wheel Bearing (long and detailed version)
This video shows how to change a pressed bearing in a Ford, specifically a 95 Ford Windstar, but this method will be similar for all pressed bearing vehicles. The main steps are to take off the spindle nut, tire, brake caliper, and rotor. Then remove the bolts from the lower control arm ball joint, tie rod, and strut. Remove the steering knuckle, then press out the bearing and hub/spindle. Then press in your new bearing and hub/spindle. This job is a little more complex but can still be easily done by any amateur mechanic. You will save $400-800 depending on your vehicle. Pleas comment, like and subscribe if you liked this video! **If the video helped, please give it a "thumbs up" and consider subscribing. Leave any questions or comments below and I will answer them as well.** My Facebook: https://www.facebook.com/chrisfix8 My Twitter: https://twitter.com/ChrisFix6 Here are some other similar how to videos (there are a lot more than this): How to change brake pads: http://www.youtube.com/watch?v=Lpb3Zms1_eM How to replace drum brakes: http://www.youtube.com/watch?v=pVrLURF7Spk How to change an Alternator: http://www.youtube.com/watch?v=byTfS1kcF1E Tags: how to remove a pressed front bearing, how to remove a front bearing, 2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed, pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy, ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly with Timken, How to remove a rusted wheel hub bearing assembly the easy way, trick, mazda, ford, lincoln, gm, truck, van, car Disclaimer: Due to factors beyond the control of ChrisFix, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ChrisFix recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ChrisFix.





Rear Wheel Bearing Removal With No Special Tools BMW 3 Series
I did the job with no special tools. Well, the only "special" tool I used is found in your plumbing department. Bearing Installation Video Here http://www.youtube.com/watch?v=DX9iCZIVgFY&google_comment_id=z12uzlzhhzn0xv scj22ngfgyskbav3hsv&google_view_type#gpluscomments





The Tire-Punishing, 400HP Turbo BMW E30! - /TUNED
The BMW E30 is quickly becoming a cult classic among the DIY, autocross, and track crowd. And though the M3 version may be climbing so quickly in price, soon no one will be able to afford one, the 325i, as it turns out, has some chops as a great platform for tuning. Kameron Baker's homebuilt E30 is just about the nicest one we've seen, and if you think it looks great, wait till you see how it drives.




Which car is faster? Which Car is Faster?





Similar 1/4 mile timeslips to browse:

2000 BMW 323i : 13.809 @ 105.480
Erick H., Engine: M52TU, Supercharger: Active Autowerke


2000 BMW 323i Sedan: 14.134 @ 100.370
N/A, Engine: 2.5L I6, Tires: Bridgestone Turanza EL42


1992 Audi 100 C4 Sedan: 14.770 @ 97.600
Mark Krankovits, Engine: 2.5 Tdi R5, Turbos: KKK K24/26 Tires: 235/35, 215/35


2000 BMW 323i Automatic (not a step): 15.339 @ 90.700
Justin L, Engine: 2.5L I6 M52TU B25, Supercharger: I wish Turbos: No Tires: Falken FK452 235/40/18


 


©2014 DragTimes - Disclaimer