How to Rebuild the Clutch of RC Nitro Engine
This is another video for RedCat Racing Arizona USA n in the tutorial
series for RC Nitro Vehicles. In this video I have shown how to rebuild the
whole clutch on a 2 stroke nitro engine using VX.18 Engine of RedCat
Racings Volcano SV 1/10 Scale 4WD RC Nitro Truck.
Beginner Nitro Engine Issues n how to fix them
I have been receiving emails where people constantly ask same questions
over and over again. Well here is one tutorial to sum up all the answers to
those questions like, Engine quits right after I pull the ignitor out, Why
my pull start snapped, Why my buggy takes off right after starting, why I
cant tune the engine blah blah. Well watch it and have fun by learning all
those concepts here.
Cleaning n Fixing the Nitro Engine Carburetor
RC Quadcopters and RC Planes, Professional aerial filming Multirotors,
Best RC videos, RC reviews, RC Aerial filming drones, Radio control drones
Higly customized and High quality Professional Multirotors, Quadcopters, RC
Quadcopter, Hexacopter, Octacopter with Autonomous flight capabilities.
Best RC Cars, RC Planes, RC Helicopters and RC toys reviews
There are times when all the settings on Low and high end valves just
doesn't work. Well this video will show you what to do and how to fix the
trouble making carburetor of your RC Nitro Vehicle. Enjoy and don't forget
to watch it on www.metacafe.com/channels/redcat+racing. There is a teaser
run at the end too :)
Nitro Engine Rebuild
Follow along with my video to learn how to rebuild your RC car/truck's
Leave any questions in the comments and I'll answer them!
And yes, I know I'm putting the old piston/sleeve back in! You need a new
sleeve/piston, wristpin, and (after about 2 rebuilds) a new conrod! I only
put the old stuff back in because it is a junker engine that I never plan
to do anything with!
40 thousand views! Thanks, guys! I'll get more videos up based on viewer
requests about basic RC aspects. Keep in mind, I cannot do many vehicle
specific tutorials, but more along the lines of general information that
everyone needs to know about RC. Send me some messages, and I'll try to get
some more up!
Nitro engine beginner problems
I get questions daily about the same thing, so this video covers well known
and well experienced problems that people have. Watch the vid, fix it and
enjoy racing. Cheers and stay tuned to http://www.youtube.com/jthornley12
TRX 3.3 modified racing engine
TRX 3.3 modified racing engine
Ported sleeve,Davis Diesel connection rod, GH-Racing head,MIP Clutch, 2.5R
flywheel,Robinson Racing Clutch bell,Integy intake and Exhaust clamps...
(yes pink fuel lines... -thanks lhs for shipping this instead of red one
that I ordered)
This is short vid of the first start(the engine was heated with hot air
blower b4 starting it)
The carb was on factory settings(hsn 4 turns), so after I lean it some, it
will really start going. -not that I even used full throttle, this is still
just first test.-sleeve and piston are used about a gallon, so they are
Basics of Nitro Engines + Tuning
Bacics of Nitro Engines + Tuning
This is a bacic introduction to nitro engines and how to tune them.
clockwise to lean out the engine (more air less fuel)
Anti-clockwise to richen (more fuel less air)
turn the needle in quarter turns, keep doing this until the engine is
there should be a little smoke and the engine should not feel sluggish or
How to leak test a nitro engine
This shows how to make a leaktest of a nitro engine. In this case a Traxxas
The same method can be used on any nitro engine. Make sure to clean it
inside after this test.