1958 Ford Fairlane 500 Two Door Hardtop Road Test - Sold Sold Sold
This 58 For Fairlane 500 two door hardtop is an original black car with the
Big Block FE 332 four barrel carburetor. Sold new in California and has the
"Black Plates" on it. it was bought by a friend of mine in 2006. He and I
went to look at another car in an Oakland but he liked the Ford so he
bought it. The car needed a restoration and his wife's father was a
bodyman, so it was a family project. The project went home and they bought
new sheet metal and parts, welded in new floor pans and rockers. The
drivers door was replaced and is not adjusted. All the other original sheet
metal was black so we expect it is original to the car. The family had some
problems, so the car never got finished. I brought the car to my place and
bolted trim back on so you can see how it looks. It has a new 2 1/2 inch Exhaust system, the new sheet metal,
front and back seat are recovered with tuck and roll. It runs great,
Original Radio Works!
This one is on the way to the Midwest. Enjoy!
1972 Ford Gran Torino
460ci big block ford, owned and driven by Justin Worley. camera man: Bill
Hammock. MSD ignition, Lunati Voodoo roller valvetrain, Edelbrock carb,
Painless wiring, AutoMeter SportComp, Optima Red Top, Mickey Thompson ET
Street Radial, Hurst QuarterStick,
Project 460 Fox Mustang Part 2
Porting and polishing the cylinder heads, assembling and firing up the 460.
This engine was built for Project 460 Fox Mustang when the plan was for a
street/strip car. After finding a super deal on a lot of go fast(er) parts,
the plans have changed. This engine will be sold and a new, more powerful
motor will be built for mainly drag racing. To see the engine run, skip
ahead to 5:50. Thanks for watching!
Specs on this engine are...
1978 460 Ford Engine Std. bore
New Speed Pro flat top pistons
new rings and bearings
new high volume oil pump and pickup
new Fox Mustang oil pan
New Edelbrock Performer RPM intake manifold
New HEI distributor
New Summit hydraulic cam .503 lift 280 duration
D3VE cylinder heads ported and polished
Holley 780 cfm vac secondary carb
Tom Fry's 427 SOHC Cammer 740HP Dyno Pull | QMP Racing
Tom Fry's 427 SOHC Cammer on the Dyno making 740hp. This engine
will be going into a '63 Galaxie and will run on normal pump gas. Thanks
for watching; remember to watch in HD!
QMP Racing is located in Chatsworth, CA
Check out our website: www.qmpracing.com
Like us: facebook.com/qmpracing
Tags: Dynamometer chatsworth race Dyno QMP engine Racing Drag Mustang Burnout turboExhaustCamaro Corvette Cars
Cobra Muscle Street Mile Supra Shelby Pontiac turbocharger Ford Paradise "Drag Racing"
"Chevrolet Corvette" Dodge Twin "Drag Race" Stock Mazda Boost HP horse power torque Run "Burnout
Paradise" muscle galaxie 63 cammer SOHC 427 nos nitro Nitrous oxide Automobiles Ls1 Z28 Holden Truck
Loud Raceway Z06 Rx7 Performance Dragster Rev Custom Viper Srt4 Rotary
428 Cobra Jet Torino
...This is my dads pride and joy, I've only driven this car twice... Really
no fun since you can't hammer it in the city limits :(
1976 Ford F-250 Ranger "Mean Green" 460 C.I. Start and Drive
In this video I start up my beloved 76 F-250 Ranger, known as "Mean Green",
shes got a bored .040 over block. 9.7:1 compression, Edelbrock intake and
Edelbrock 4 Barrel 750 CFM Carb, MSD Distributor and coil, RV cam, and
slightly milled heads. Estimated horsepower is in the 350 to
400 range with somewhere around 400 to 500 ft lbs of torque, I know this
from the power adder combos I have used that are discused on ford truck and
460 engine forums that what I have should make the amount of power I say it
Watch the video, and you decide what you think!!