Pontiac 535 engine by Tin Indian Performance 1000+ Horsepower ideling on dyno
This is the current combo that is in the Tin Indian Performance Dragster. Combo features a MR-1 cast iron block, forged crankshaft, GRP Rods, Ross Pistons, Total Seal rings, Custom camshaft, KRE 400 CFM High Port Heads, KRE Sheet metal intake with CNC'ed runners and 2 1250 holley dominator carbs. Special KRE made Tri-Y headers, and Star Machine vac pump. This combo makes 1013 hp @ 7800 rpm and 769 ft lbs of torque at 6200 rpm. This engine has taken our TIP dragster a best of 7.14 @ 186.51 at Norwalk Raceway Park in September 2009! www.tinindianperformance.com
Norwalk Pontiac Nationals 2012
This video covers my brothers car "Krusty" qualifying for the Quick 16 and
our friend Rodger with his Blown alcohol 69 GTO. Arnie Beswick is also in
the video and the rest of the quick 16 cars.
Tony Bromley's 400 to 460 stroke Pontiac Dyno Pull | QMP Racing
550 torque @ 5800rpm
535hp @ 4000rpm
For those of you paying attention and noticed the numbers aren't the same
on the screenshot, its because we made another few runs, but didn't tape
them. We'll upload a pic soon.
QMP Racing is located in Chatsworth, CA
Check out our website: www.qmpracing.com
Like us: facebook.com/qmpracing
qmp racing quarter mile race car engine motor custom high performance
chatsworth California hp horse power torque trq Dyno rpm turbo drag Exhaust run Boost psi dragster raceway nitro Nitrous super Supercharger muscle burnout idle motorsports Mustang cam Ford hydraulic
Street pontiac Cars Supra "Drag Racing" Pontiac Shelby Dodge Twin Stock
Mazda Ls1 Motorcycle Bike
Pontiac 461 Stroker On Test Stand SEE END!
LAST 10 SECONDS OF VIDEO ARE BEST!! Here is my Pontiac 461 Stroker with
Open Race Headers on home built Dyno test stand. This engine
features Edelbrock heads, Hooker Supercomp Roundport Headers, and a few
other tricks. Makes 535hp, 595/ftlb tourque. Now installed in my black 69
World's Fastest Pontiac 6.27 @ 228mph
Rodney Butler sets both ends of the tradional Pontiac power record with his
twin turbo 63 Tempest. Congrats to
Rodney & Travis & the rest of the team. In the other lane John Welter Is
getting it done with a 6.92 @ 199mph
Pump Gas Pontiac engine 468 cid by Tin Indian Performance on the dyno 558 hp 583 ft lbs of torque
This is a 468 cid Pontiac engine we build to Mike Matuszek and his '66 GTO.
The engine is based off a 455 cid pontiac block. An Eagle crank and rod
combo was used on the bottom end along with a set of KB forged pistons. A
Tin Indian Performance custom ground Comp Cams hyd roller was also used
with Comp Cams hyd roller lifters. The engine is topped off with Performer
RPM cylinder heads and intake. We also used one of our custom 4150 1"
spacers with the 950 cfm quick fuel carb. The combo pulled 11" of vac at
850 rpm! It made 558 hp @ 5400 and 583 ft lbs of torque @ 4500 rpm. ALL
ON PUMP GAS!!! Watch those brand new Doug's Headers turn blue on the pull.
PONTIAC - "The Super Duty Story" Part 1 of 3
Pontiac had an SD engine program in the late 50s early 60s, and
later/briefly again in 1973/74 with the SD455. This video is regarding the
FIRST Super Duty program.---In only a few years time during the late 50s
early 60s, Pontiac MORE THAN DOUBLED their V8's horsepower output (described
in this video), while using/keeping the same V8 engine block they used thru
1955-81. Even though the same block was kept, from 1955-62 the cubic inch
displacement grew much larger than the initial 287 cuber it started as in
1955. It grew to a 317 347 370 389 and finally a 421 cuber in 1962. It
eventually maxed out at 455 cubes in 1970. By 1970 ALL the other GM
divisions were producing engines at 454 or 455 cubes (500 for Cadillac).
PONTIAC WAS THE ONLY DIVISION still using the same block they used in the
1950s on engines that had a much smaller displacement -- 287 cubes. The
1955 287 displacement would remain the smallest displacement ever used in
the Pontiac V8 block all the way until 1980/81 when a 265V8 was produced.
Since less durability was required for the smaller displacement, the block
was decked/butchered/lightened on the 265/301v8s of 1980/81. Prior to 1980
the block had never been decked/butchered/lightened. The 1980/81 265/301v8
blocks were about 200 pounds lighter than the 1955-79 blocks, and only 25
pounds heavier than a Buick 231V6.
Splitter's 541 Inch Pontiac Engine V8TV
http://www.v8tvshow.com - We turned to the Pontiac pros at Butler
Performance for insight on building Splitter's street / strip / road course
engine. This one has to do it all, so the parts need to be carefully
chosen to get the job done. David Butler takes us through the parts and
explaines his choices.