*READ THE FREAKING DESCRIPTION PLEASE** 305 small block chevy out of my 86
elco ORIGINAL ENGINE BUILT FOR SOUND NOT POWER.bored .40 over 350 heads
ported and polished by me. comp THUMPR cam .305/.305 lift .287 duration
comp double roller timing set edelbrock performer intake holley 600 cfm vac
secondary carb accel 60,000 volt ignition 160lbs compression. motor is now
sold for the 305 haters this was a strong reliable motor. and yes im aware
the video is dark i finished the motor in the dark and decided to make a
quick video of the first fire up. the nect day it was in the car which
THERE IS ANOTHER VIDEO ON MY CHANNEL OF IT IN THE CAR WHERE ALL YOU
TROLLERS CAN WATCH THE PAINT DRY AS IT IDLES GOOD LORD!!!
sound of Flowmaster 10 single chamber on small block chevy
Got a new muffler. Here's the different sounds for your reference in case
you're thinking about an Exhaust
'85 GMC C10, 305, quadrajet, THM350 transmission. No catalytic converter.
Here's the three different sounds. First one is the old muffler with dumps.
Second one is straight pipes after I cut the old muffler off. Third one is
the new Flowmaster 10 single chamber with dumps.
ZR1 Vette vs Jet! - Chevrolet Corvette ZR1 Races A U.S. Navy Fighter Jet
MT Editor at Large Arthur St. Antoine pits Chevy's awesome "Blue Devil" --
the Corvette ZR1 -- against its toughest adversary yet: a Blue Angels
F/A-18 Hornet fighter jet.
Shot By: Jim Gleason & Terren Lin
Edited By: Jim Gleason
Read the story here:
Nasty chevy 305 400hp
400hp 305 ported heads custom camshaft 850hp holley dp 9.5:1 compression,
just spare parts i had laying around. file fit moly rings stock crank and
stock pistons with 80,000 miles just new bearings. I built this engine for
the burnout competition for car craft, after car craft in goes the big
block. just hope i finish painting it....
Flowmaster Muffler Comparison
A raw test of 7 different Flowmaster mufflers on one motor.
The Motor -
Small Block Chevy 406, 11:1 compression, Crane Solid Roller Camshaft,
Brodix heads with 2.05- 1.60 titanium valves, Eagle 4340 Crank, Eagle H
beam Rods, Manley Forged pistons, Victor Jr Intake manifold, 850 Holley DP,
K&N air filter, Moroso 7 qt. pan, 1 7/8 headers, BE COOL radiator with dual
13 inch fans, MSD distributor, MSD coil and MSD 6AL box.
Exhaust - Flowmaster 3 inch Scavenger
Engine Rebuild class (the engine WORKS!!)
Our nasty Chevy 350 runs.
Motor: Chevy 350, 4 bolt main, .30 over,
Left head: 350 head, Right head: Chevy 305.
History: Came from a local junk yard, all bearing were fried, rings shot.
Oil vally was painted a pretty gold (old racer trick to make the oil flow
better : Didn't work)
Last owner just frankenstein it together.
Goal: needed to fire-up and runs for a few secs.
Summer class 2009 glendale community college AZ
Replacing valve stem seals in 305 H.O. small block chevy from 1986 Monte Carlo SS
I'm putting the original 305HO back in the Monte after taking the ZZ3 out
for my Iroc project. This is mainly to make the car mobile but it may end
up tagged with this engine for a while. Previous owner reported that this
305 has over 100k miles on it and has been out of the car since 1997. He
said it smoked during startup and sure enough the valve stem seals were
worn out. Hopefully this will fix the issue.