Remove Rust from Metal and Panels the Easy Way: Video 2
"No abrasives required" Ready for panel and paint immediately!
Nothings more cost effective than being able to do your projects from your own garage. You can even turn this into some extra cash flow, and to start it won't even break your bank balance. Nothing is worse than completing your project and finding six months later you have a blister in the painted surface. With this method, "I know all the rust is gone"
Using citric acid for rust removal
Citric acid can be bought from drugstore (they use it in jelly or such to
adjust acidity) but it is very expensive there. Therefore Finnish rodders
buy it from some agriculture-store. It is not expensive. Officially it is
used as pigs obstruent! I dipped those parts in citric acid for overnight,
next day brushed it with wirebrush and flushed it with water. Then again
back to citric acid over night and wirebrushed + flushed it next day.
Flushing is important, you'll want to get all acid away, otherwise steel
will turn to yellow.
You can't use this method on all parts because of hydrogen embrittlement.
So no pedals, frames, brake drums, engine blocks or such to citric acid!!!
And yeah, parts should be clean -I've cleaned 'em with fuel- because grease
will neutralize acid. Ratio was 3%
Parts must be dried soon as you get them flushed, I quess you guys know
Music on the background:
Junior Brown; "Sugarfoot Rag"
57 Tulsa buried 1957 Plymouth Belvedere Boyd Coddington
Tulsa Story :This is a video pictorial of the 1957 Plymouth Belvedere that
was buried in
Tulsa, Oklahoma on June 15, 1957 as a time capsule. It was uncovered 50
years later on June 15, 2007.
I was hoping to see a pristine version of "Miss Belvedere", but as it
out, the vault leaked and filled with water, causing much damage to the
automobile. As a car enthusiast, I watched the story develop over the
few years. I waited and watched it live online as she was extracted from
the ground. When I saw the rust-colored dirt and muck on her, I had a bad
feeling about her condition.
I wish the person who won this car (by guessing the closest to the town's
actual 2007 population back in 1957) could have it restored, but that would
be a massive undertaking. On the other hand, she should get a chance to
I hope you enjoy the video, along with some before, during, and after
update the winner of this car was
Raymond Humbertson died in 1979
he was Marine and a Korean War veteran
he has 2 sisters who may inherit he car
Miss Belvedere Moves On
By Old Cars Weekly
After spending nearly 50 years quietly rusting beneath the Tulsa County
Courthouse lawn, the 1957 Plymouth Belvedere affectionately known as "Miss
Belvedere," is on the road once again.
Don't get too excited, when she rolled out of Tulsa earlier today, it
wasn't under her own power—she was whisked out of town in the back of a
After months of legal wrangling to establish ownership of what is clearly
the most famous "finned" Mopar in the world (yes, even more famous than
Stephen King's "infamous" Christine), Miss Belvedere has begun her journey
to New Jersey — and possibly a rust-free future.
Levada Humbertson Carney and Catherine Humbertson Johnson, elderly sisters
from Maryland, will officially take possession of the Belvedere as
beneficiaries of their brother Raymond Humbertson who won the car as part
of a contest held back in 1957.
Buried with the car was a time capsule containing people's guesses as to
what the population of Tulsa would be in 2007. Included among the hundreds
of guesses, was one made by Raymond Humbertson of Cumberland, Md., who died
in 1979. His guess was only 2,286 off the actual census numbers, closer
than any other entry.
Assisting the cars elderly owners will be Levada Carney's son Robert Carney
and Dwight Foster, President of the UltraOne Corporation.
As you will recall, as part of this ongoing saga, New Jersey-based
UltraOne, manufacturer of a line of rust removal products, will now begin
the pain-staking process of de-rusting and preserving what remains of the
According to Robert Carney, the car, which suffers from extensive damage
after being submerged in conditions described as a "watery grave" for an
unknown number of years, may eventually be able to take to the road under
her own power.
Once Miss Belvedere arrives in New Jersey she will undergo a lengthy
cleansing and rust removal process that her new owners and the folks at
UltraOne hope will stabilize the car before sealing it with a clear-coat
designed to halt the rusting process.
"We will not be restoring the car but preserving her for the future," Mr.
Foster told the Tulsa World. "We have to stop the rust, because if nothing
is done, this car will be dust in two years."
According to the UltraOne Web site, future plans for Miss Belvedere could
include a second Tulsa unveiling and a tour around the country for special
events. Following the tour, the car's future remains unclear.
However, it has speculated that the car could find her way to the
Barrett-Jackson auction block in Scottsdale in the coming years.
we will miss you the legend Boyd Coddington,
Soda blast your car
Serving all of South Florida call Sodablasters of South Florida's mobile
service or drop it off at our location in Hialeah. Visit our website for
more information. We also remove bottom paint from boats, graffiti, mold
and smoke damage.
"Stripping Paint" ....Fast from any Car Doorjams.
Removing the paint from car door jams has to be one of the worst jobs to
tackle on any project. Here I compare a couple of discs to show you which
is the better choice for you, making your job a heck of a lot easier.
How To Remove Rust from a Brake Rotor
Facebook Page: https://www.facebook.com/MetalRescue
We de-rust a brake rotor that is completely full of rust. Within
approximately 2 hours the rust on the rotor is completely removed. Our
satisfied customer even says that Metal Rescue™ may have made his part
look better than it did straight from the factory! Metal Rescue™ Rust
Remover Bath is non-toxic, water-based, and biodegradable. It is safe on
everything, except rust!
DIY POR 15 - How To Prep Rust Before Applying POR15
For Auto Body and Paint Supplies visit
http://www.CollisionBlast.com/Supplies For FREE access to training at
http://CollisionBlast.com DIY Por 15 Part 1 - How To Prep Rust Before
Applying POR 15 using Marine Clean and Metal Ready.
For rusted metal, such as the floor board on this Mustang, there are two options when
prepping for POR 15. The first option, I am going to demonstrate in this
video. The second option is to have the metal blasted to bare metal.
MARINE CLEAN is a complex mixture of organic & inorganic chemicals. It is
non-toxic, biodegradable, water-based, and has no noxious odors nor
chlorinated solvents. It doesn't contain any petroleum products and has no
flash point. Marine Clean repre- sents a revolutionary breakthrough in
cleaners, degreasers and dispersants.
Use MARINE-CLEAN for cleaning and degreasing machinery parts, turbine
blades, diesel engines, compressors, transformers, bulkheads, deck plates,
bilge areas; removal of oily deposits found in closed systems such as air
conditioning, boiler tubes, compressor lines, heat exchangers and coils;
removal of light distillates, mineral oils, heavy grease, degreasing all
metal surfaces, plastics, wood, fiberglass, painted surfaces. Always wear
eye protection and rubber gloves when using Marine Clean.
PREP & READY provides the best adhesion for POR-15® on any metal surface,
including aluminum and shiny polished metal surfaces. Our simple process
gently etches metal, creating an ideal anchor pattern for coatings such as
POR-15®, while simultaneously leaving a zinc phosphate coating to insure
chemical bonding of paint and steel. Avoid other preps that may leave
harmful residues which prevent proper adhesion. After thoroughly degreasing
your work piece, apply environmentally safe PREP & READY to both neutralize
any rust and etch any clean bare metal. This will allow better adhesion of
POR-15® or any other paint. PREP & READY is not caustic, corrosive, toxic
Also be sure to subscribe to this YouTube to stay tuned with upcoming
videos every Tuesday at
Learn how to adjust a spray gun by watching my spray gun adjustment
playlist at http://www.youtube.com/playlist?list=PL9D278D201EBFA3B6
Join me on Twitter at http://Twitter.com/DonnieSmith7
Join our Facebook page at http://Facebook.com/CollisionBlast
For free access to DIY auto body and paint training, please subscribe to
Collision Blast at http://CollisionBlast.com
Thanks for watching the my videos, and be a resources by sharing the links
to the videos with your friends on Facebook and Twitter.
Licenced track: Michael Conn "Dare"
The Save Old Cars Project
The song is "Dust In The Wind" by Kansas
I do not own this song or any of the used pictures.
-Never crush old cars-
How to fix a scratch & stone chip with spray cans.
In this episode of Custom Spray Mods Dave shows a complete step by step
guide on fixing a scratch and a stone chip in your paintwork.
Includes sanding, primer, paint, clear and Buffing.
Using this method the finish you get will look great. And its all done
cheaply and easily.
Click here to purchase the Scuffing paste and pads used in this video.
Preval DIY Spray Can Unit
Music by DanoSongs
Music by Kevin Macleod http://incompetech.com
Music by Ignyte: http://www.youtube.com/DJignyte
All products available at
VG Auto Paints
How to fix a scratch
How to paint with spray cans
stone chip auto paint spray