Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Replacing a Rack & Pinion Type Inner Tie Rod DIY

Thanks for watching! Rate & comment on this video, then check out my channel & SUBSCRIBE for more DIY auto repair videos. This is a video showing how to replace an inner tie rod on a rack and pinion equipped vehicle. This on is a 1997 Ford Explorer 2 wheel drive. I made a brief reference to a zip tie on the video & didn't explain myself. I used a zip tie in place of the inner bellows boot clamp on the rack.


 


More Videos...


Bearing Making Noise? Fix it Before This Happens!
Thanks for watching. Please comment, rate, subscribe, and check out my channel for automotive repair how-to videos. This is video of a Ford Explorer / Mercury Mountaineer that lost a wheel on the interstate. The vehicle had to be making some serious noise for a long time before the wheel finally let go. The caliper bracket was all that was holding the wheel on until it broke. The people in the Exploder should be glad the thing didn't flip or hit any other cars. Next time you're riding down the road look at the car beside you or coming towards you. This could happen to any poorly maintained vehicle at any time. Be careful out there.





Front Suspension & Steering Inspection
I've had a few requests lately, asking how to determine which front end part needed to be replaced. I try to show how to check the inner tie rods, the outer tie rod ends, and the upper & lower ball joints. This is a combination of 3 different videos on 3 different vehicles. I hope this helps.





How to Replace An Electric Fuel Pump
Thanks for watching! Please comment, rate, & subscribe. This video is how to replace an electric fuel pump inside the fuel tank of a 1997 Chevrolet Tahoe.





First Look: Lifted 2014 Chevy Silverado 1500
I got a new camera & some new video editing software, so we'll see how this goes... This is a brand new 2014 Chevrolet Silverado crew cab that we lifted today @ work. It has a Pro Comp 6" lift & 325/60/20 BFGs. I added a little something extra at the end of the vid.





How to Change Tie Rods (inner and outer tie rod ends)
How to replace inner and outer tie rods, How to replace tie rod ends, How to replace tie rods. How to check to see if your tie rod is bad: https://www.youtube.com/watch?v=brI2feYiEi8 Tie Rod End Cutaway: https://www.youtube.com/watch?v=3RjhtVse6jE This video will show you in depth how to change the inner and outer tie rods of your car or truck. You need a special tool, an inner tie rod end tool, to complete the job (this can be rented for free at your local parts store). The job straight forward and anyone with basic tools can do it! **If the video helped, please give it a "thumbs up" and consider subscribing. Leave any questions or comments below and I will answer them as well.** My Facebook: https://www.facebook.com/chrisfix8 My Twitter: https://twitter.com/ChrisFix6 Subscribe: http://www.youtube.com/subscription_center?add_user=paintballoo7 How to replace Drum Brakes: https://www.youtube.com/watch?v=3FYRwfKNHxw How to replace Differential Fluid: https://www.youtube.com/watch?v=KmqMUJb-E4M How to fix a Squeaky Belt: https://www.youtube.com/watch?v=UF3W-vHPYHg How to replace a Wheel Bearing: https://www.youtube.com/watch?v=BPs-QALECqs Replacing a Rack & Pinion Type Inner Tie Rod DIY, How to change a tie rod on your vehicle, tie rod replacement, tie rod end replacement, tie rod end check, tie rod noise, tie rod end removal, tie rod end, tie rod removal, tie rod adjustment, tie rod, fix tie rod, tie rods, tie rod ends, inner tie rod, outer tie rod, tierod, toyota camry alignment, tj death wobble, yukun tie rod, u-joint replacement, ball joint separator, bellows boot, steering rack boot, camry tie rod, k30 tie rod, steering parts, alignment wheel, wheel alignment, satrun tie rod, saturn tie rod, tierod adjustment, tie rod adjustment, tie-rod, separate tie rod, tie rod separator, tie rod adjuster, Disclaimer: Due to factors beyond the control of ChrisFix, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ChrisFix recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ChrisFix.





1999 Civic Power Steering Rack Replacement (Part 1) - EricTheCarGuy
1999 Civic Power Steering Rack Replacement (Part 1) - EricTheCarGuy This video is a step by step power steering rack replacement on a 1999 Honda Civic. It covers some key tips on power steering rack replacement that will also apply to other makes. Remember that when doing this job you will also need to have an alignment done once the job is complete otherwise you may experience extreme front tire wear. A link to part 2 will be posted here when it is made live. https://www.youtube.com/watch?v=ttKBE4QdTJ0 Visit me at: http://www.ericthecarguy.com/ Music by: EricTheCarGuy --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Tacoma Tie Rod (Inner & Outer) Replace
This video shows how to install tie rods (inner and outer) on a 2001 Tacoma. Instructions can be applied to 1996-04 Tacoma, 4Runner and PreRunner.





How To Replace CV Boots - EricTheCarGuy
How To Replace CV Boots - EricTheCarGuy http://www.ericthecarguy.com/ This one is a request from more than one person so I'm happy to bring it to you. As I said in the video I personally don't see much point of replacing just the CV boots anymore as it just makes more sense to replace the axle, that's just how I feel however. If you do want to replace the boots I hope this video will help. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to Tell if Your Inner Tie Rod is Bad
Get an inner tie rod wrench set on Amazon HERE→http://www.amazon.com/gp/product/B0002SRGFW/ref=as_li_qf_sp_asin_tl? ie=UTF8&camp=211189&creative=373489&creativeASIN=B0002SRGFW&link_code=as3&t ag=httpwwwyou00f-20 Here's a link for the boot band tool on Amazon (I have to say that) HERE→http://www.amazon.com/gp/product/B0002SREPY/ref=as_li_tf_tl?ie=UTF8& camp=211189&creative=373489&creativeASIN=B0002SREPY&link_code=as3&tag=httpw wwyou00f-20 How to Tell if Your Inner Tie Rod is Bad





Rack & Pinion R&R
Rack & Pinion steering gears look like they are really hard to replace. Sure, some are more difficult than others. But many are not that bad. The Ford Escape, Mercury Mariner, & Mazda Tribute are all the same vehicle and have the same steering system. Here is how to replace it.





Installing a new Rack and Pinion 2003 Dodge Grand Caravan
My rack and pinion and power steering pump died out, and instead of paying $500 for the rack and $300 for the pump to be installed I did it myself..Pump was inter warrantee, rack and fluids cost under $100.00





How to Perform an Alignment on Your Car at Home
TheCousinDan shows you how to align the steering on your car at home. All you need is a piece of fishing line, a tape measure, a marker, and some buckets.





Oops, Axle and Ball Joint Replacement - EricTheCarGuy
Oops, Axle and Ball Joint Replacement Sorry I missed you last week, I had this video half done and didn't get a chance to finish. Well we have our 1990 Accord again, I'm getting some mileage out of this one but I don't mind cause there are still quite a few of these on the road and a few of you have claimed ownership to one of these 4th generation Accords, so enjoy. A couple of things to note, I could do a video on taking out the wishbone bolt alone, I've run into a few problems here such as a rusted bolt that won't come out of it's bushing as one example, perhaps future videos will show how to overcome this problem. I thought this one went together well despite the fact that you might be getting sick of Honda Accords, I still have more from other makes that I haven't edited or posted yet. I have more to this video as well that may show up in DVD form at one point, YouTube only gives me 10min to work with but I think that is enough to get you started and not lose interest. Perhaps you could help by submitting questions in the form of text responses or what I would really like is a video response to something I've put out there, that would be great. Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to Troubleshoot and Fix a Rack and Pinion for Steering Problems Like Stiffness, Pull, Wander
Hard to steer? Don't pay a mechanic! Step-by-step instructions to diagnose, service and troubleshoot a rack and pinion on automobiles. This video covers testing, installation and operation of a rack and pinion with advice on properly bleeding the steering system fluid. Sponsored by BBB Industries - makers of premium alternators and starters that meet or exceed OE form, fit and function. http://www.BBBind.com Related Videos: How to Troubleshoot and Fix a Noisy, Stiff, Sticking or Binding Power Steering Problem https://www.youtube.com/watch?v=4RRbFiro4ps Power Steering Gear Box Testing, Troubleshooting, Removal & Replacement https://www.youtube.com/watch?v=dAk083N7nuE How to Bleed a Power Steering System (PDF): http://www.revbase.com/tt/sl.ashx?z=ef3c1f2&dataid=261671 Hosts John Gardner and Chase Vlieg are ASE-certified Master Technicians and instructors at Chipola College's Automotive Service Technology Program.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

2014 BMW 550i XI: 11.735 @ 118.290
Anes Radoncic,


2013 BMW 550i BMS stage 2: 11.911 @ 118.060
Sergey SPR, Tires: Hankook V12


2013 BMW 550i XI BMS stage2: 11.943 @ 117.940
SergeySPR ,


2014 BMW 550i XI: 12.058 @ 115.850
Anes Radoncic, Tires: All Season ( NON RUNFLATS)


2013 BMW 550i XI: 12.177 @ 115.390
SergeySPR,


2013 BMW 550i xi: 12.191 @ 114.740
SergeySPR ,


2014 BMW 550i XI BMS STAGE 1 TUNE: 12.192 @ 113.480
Anes Radoncic, Engine: BMS STAGE 1 TUNE,


2013 BMW 550i xi BMS stage1 : 12.247 @ 114.760
SergeySPR ,


2013 BMW 550i Xdrive: 12.363 @ 112.660
SergeySPR ,


2013 BMW 550i 550 xi Dinan Stage 2: 12.380 @ 112.380
Elise C/mike s, Engine: 4.4 twin turbo, Tires: Stock Goodyear LSAs


2011 BMW 550i xDrive Dinan Stage 1 Tune: 12.485 @ 110.830
Mo Rafizadeh, Engine: Dinan Stage 1,


1976 Chrysler Cordoba : 12.620 @ 112.460
Adam Horwatt, Turbos: would be nice Tires: 275/60/15 M/T drag radials rear


2013 BMW 550i Xdrive: 12.798 @ 107.940
SergeySPR,


2011 BMW 550i Sport Package: 12.920 @ 109.290
Stephen F Karp, Engine: 4.4 Liter V8, Turbos: Twin Turbos


2012 BMW 550i Dinan Stage II: 12.999 @ 112.950
alextremo, Engine: 4.4L V8 TwinPower Turbo,


2011 BMW 550i : 13.139 @ 108.400
Jorge O,


2008 BMW 550i : 13.310 @ 105.010
NA, Engine: V8, Tires: Continental ContiSportContact 2


1978 Chrysler Cordoba : 13.410 @ 103.000
j connet, Engine: 400, Tires: 235-60-15 ft 295-50-15 r


2006 BMW 550i ZSP: 13.510 @ 105.010
RT,


2007 BMW 550i : 13.701 @ 104.120
NA, Tires: Bridgestone Potenza RE050A


 


©2014 DragTimes - Disclaimer