701hp S2000 From Hell-Part1
701whp S2000 tuned and built by T1 Race Development. Car has bone stock
motor, tranny, and rear end.
***S2K never saw the 701whp in this video, highest hp was around 600whp
against the GSXR1000***
All you haters that think its not really pushing out 701whp heres the Dyno video...faggots
and the music is kanye west 808s and heartbreaks and linkin park, no more
How to Rebuild a Turbo - Part 1 of 2
Rebuilding a td05h 16g turbo. This
process can be applied to many journal bearing turbochargers. :) It definitely comes in handy to
know how to do this when you are in this type of hobby.
4/25/12: Small explanation on the balancing of the rotating assembly since
I get so many comments regarding it. This particular turbocharger, td05h, has it's rotating assembly
components balanced separately. This means each individual part (compressor
wheel, turbine wheel/shaft) gets balanced separately. This allows for easy
interchangeability of parts in case they need replacing. This is why I am
able to install a td05 20g wheel on this turbo without having to balance the entire
rotating assembly. THIS IS NOT THE CASE FOR ALL turboS OUT THERE. You need to research whether
your specific turbo (if it's not td05h)
was balanced as an assembly or "component balanced" like I explained above.
I hope this information helps. Good luck in your projects. Stay Boostin'
keywords: turbocharger dsm eclipse talon
awd gsx tsi fwd gst mitsubishi evo evolution lancer 14b 20g td06 td06h td05
install installation upgrade race vs Boost supra wrx sti toyota subaru Dyno laser rs rst 13g hx35 hx40
holset 18g 25g sbr t25 stock replace rebuilding big large nissan 240sx t28
How To Clean Civic Type R Headlights with Toothpaste
We show you how to clean the misty haze layer that can appear on your
plastic headlight lenses over time making them look dull and transform them
into new shiny headlights!
All you need is toothpaste and a cloth!
Click here and SUBSCRIBE for more videos like this!
LIKE our CTR EP3 Facebook Page:
LIKE our TechTuners Facebook Page:
Civic Type R Oil Change Tutorial
Remove & Paint Civic Type R Rocker Cover
How To Replace Civic Side Lights (Facelift EP EP3 2004 - 2005)
Heko Wind Deflector Civic Type R EP3 - Fitting Tutorial
Watch our VTEC Compilation:
Red JDM Civic Type R Floor Mats
Honda Accord VTEC Solenoid Gaskets Replacement
In this video I show you how to replace both VTEC solenoid valve gaskets
(valve to cylinder head and solenoid to valve) on 1994-1997 Accords.
This is a common cause of oil leaks on the upper passenger side of the
engine next to the distributor shaft seal, distributor o ring, and valve
It seems the same engineers who buried the Accords fuel filter also decided
to make the VTEC solenoid valve difficult to remove as well. One of the
bolts for the valve is buried so deep you have to partially drain the
cooling system and use a u-joint to get it out.
I take your through the process step by step from removal of all the parts
to re installation.
This video ran a bit longer than I wanted it to but considering how
deceptively easy this job looks at first glance (until you can't get that
one remaining hidden bolt on the valve off to remove it) I decided to leave
in as much detail as possible.
You will need to add new coolant and bleed the cooling system to avoid
engine damage after you're done. If you need that info here is the link to
my cooling system bleeding video.
Honda part numbers used in the video:
Solenoid to valve gasket: 36172-P0A-005
VTEC valve to cylinder head gasket: 15825-P0A-015
VTEC oil pressure switch o-ring: 91319-PR3-003
Thermostat housing to intake gasket: 91312-P0A-000
Thermostat housing to connecting pipe o-ring: 91314-PH7-003
These part numbers should work on all 1994-1997 Accords with VTEC but as
always check with your dealer to confirm these part numbers will work with
Intro and outro music by Kevin Macleod (Incompetech.com).
HONDA V-Tec Operation
HONDA V-Tec Operation
Get the book here: https://www.createspace.com/4321251
Describes the operation of the HONDA V-Tec variable valve timing system.
Like never seen before, this animation goes into details on the mechanical
principle of the V-Tec system. The Honda V-Tec system is a dual setting
variable valve timing system. It is meant to give high efficiency and low
power at lower RPM and high power and low efficiency at higher RPMs. There
have been a few incarnations of V-Tec, which came out in the late 80's, but
their principle is the same. See it all here with high quality visual
Amazon Printed-Books & Kindle:
Google Play Android APPs:
Amazon Video DVDs:
Barnes & Noble Nook:
Apple iTunes iPad:
Turbo Integra Type R vs Nissan Skyline R35 GTR
Integra was running 11.6-11.7s all day but had a bad run. This pass the
Integra Spun and only had 1.9 60ft on 24.5x8.5x15inch slicks. Integra makes
380whp GTR is stock. GTR cost 93,500. Integra owner has $8000 in to whole
GTR runs 12.093 @123mph
ITR run 12.540 @120.72
Search "ITR first pass ever" for 11.6 pass