The Best Burnout EVER!!!!
$300.00 special catching HELL!!! At the 2011 Burnout party!!!
This vehicle was bought to finish the show with a bang!! This was done in
front of the house on a PRIVATE road and IF YOU DON'T WANT TO SEE A BURNOUT
DON'T CLICK THIS LINK!!! And don't ask WHY?? If you want to see pics of the
road after the burnout go to my channel click on website!!!
Sexy Dayanis Garcia takes ride in a 900hp Evo IX
During a photoshoot with Joel Antoine Photography we took a short break to
take Dayanis for a few pulls in the 900hp Evo IX. Enjoy!
2.2 liter stroker billet crank
Force Performance GT3794 HTA
Custom built transmission from TRE with an HKS 4:11 final drive
Music : Sadik Beatz -- Rock (Dubstep Beat)
Evo Cams Out
**ALL MODS ARE IN MY DESCRIPTION**
My 2005 Mitsubishi Lancer Evolution VIII Idling with 9.5:1 Compression, FP
HTA73 Green turbo, GSC S2 Cams, PTE
1000cc injectors, Supertech 1mm oversize valves and springs, GSC Chromoly
bases and retainers, HKS Carbon TI Exhaust and much more....... Some exterior mods
are: 18x9.5 Rota P45r/Direzza zr1 star spec 255/30/18 combo. REAL jdm rear,
painted viii tails, Rexpeed carbon lower trim, and more.....
evo VII accelerating
my humble evo VII accelerate...HKS hi-power full Exhaust system with HKS SSQV and Tial
wastegate...watch in HQ..turn up ur speaker volume..
If you liked this video than you got to watch part 1
http://youtu.be/vCeQ_9nWTVk THANX FOR WATCHING AND SUBSCRIBE TO MY CHANNEL
Rita (opala)- difusor de escapamento
galera to vendendo o opala do video olha o link ai
EVO 9 vs WRX STI LOUD FULL THROTTLE LAUNCH!
http://razzi.me/johnirvine for my high quality photos
http://www.facebook.com/IrvineBrothersPhotography - visit and "like" my
page for exotic car photos
see my videos on http://supercars.tv/jirvine/
Which would you choose? comment below! I didn't have time to run back and
get my dslr in the car
How to Change a Wheel Bearing (short and fast version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.