Toyota Camry Timing Belt
TIMING BELT REPLACEMENT - 2.2L 5SFE - Toyota Camry
Toyota Camry Timing Belt Replacement
Category:
Autos & Vehicles
Tags:
Timing Belt Replacement
Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. Ensure idler pulley is clean and rotates smoothly.
2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly.
3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.
CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence.
5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket.
6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification.
7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover.
8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover.
12.Tighten No. 1 idler pulley bolt to specification. Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification.
13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification.
14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.
Pt. 2 of 2: Timing Belt Service 7th Gen Honda Civic
CGHQ Website: http://www.classicgamershq.com
Subscribe: http://www.youtube.com/subscription_center?src_vid=cTUDMqGVZTQ&add_user=big2000dave&annotation_id=annotation_456191&feature=iv
Facebook: https://www.facebook.com/pages/Classic-Gamers-HQ/206873449382847
Twitter: http://twitter.com/#!/classicgamershq
Part 2: This is a fully detailed timing belt service for a 2001-2005 Honda Civic 7th generation vehicle. We replace the timing belt, a/c and alternator belt, power steering pump belt, water pump, auto tensioner, and crank shaft seal. This is a step by step procedure to do this service successfully with a bit of time and patience. Be sure to subscribe. Thanks!
PART 1: http://www.youtube.com/watch?v=zUjHS_gmmMQ
Also check out the aftermath, motor mount repair video:
http://www.youtube.com/watch?v=G0NmnGS6V1k
Audi Timing Belt
This is a video of a Timing Belt being changed on an Audi V-6
Hubitools Universal Timing Gear Clamp
Find out about Hubitools Universal Timing Gear Clamp that easily and efficiently holds valve timing on overhead cam engines during timing belt service.
How to: Replace a timing belt and water pump - part 2
In this video I explain and show the steps required to install a timing belt and water pump. The steps and difficulty for this will be different on some cars.
The steps and techniques for replacing the timing belt and water pump that are shown in this video will be similar,if not the same,on Honda 4 cylinder engines.
This video should be used as a basic guide and you should always consult your manual before performing maintenance on your vehicle.
Ebay Warning
A warning about Ebay sellers, I bought a car from a seller because of what the add read, now I know that some people will lie just to get a sale.
I did post this video on another channel last year, and it had quite a lot of views, views I think wasted as they could be collected here instead.
This video shows some of a project in which my dad and myself tried to repair the head gasket on a k-series Rover 416, if only it was as simple as that.
The background music was written and played by http://www.youtube.com/user/PaulSaywood please subscribe to that channel. facebook: http://www.facebook.com/pages/G4rdenspoon/284634921659121?ref=stream
AC System Basics - EricTheCarGuy
This is a kind of video response to a question I got from RadicalComedy about servicing her AC system. Keep in mind that this is a very basic overview of the components and operation of the AC system. In future installments I plan to get more in depth about the operation and function of these parts but for now I think 6 minutes of your time is enough.
Visit RadicalComedy's channel
http://www.youtube.com/user/RadicalComedy
Visit me at EricTheCarGuy.com
http://ericthecarguy.com/
Visit EricTheCarGuy Forum
http://www.ericthecarguy.com/forum/default.aspx
Visit my Facebook Page:
http://www.facebook.com/EricTheCarGuy
Stay dirty and cool if you can.
ETCG
