BMW 330ci AFE Style Exhaust
02' 330ci... Basically stock. Minor intake work, but stock otherwise under
the hood. The Exhaust setup is
basically a muffler delete with a res tube after the rear axle bend. Dual
pipe into a 3 inch all the way to the tips and a smaller res pipe. Sounds
much better in person than it does on video, especially from a still
picture camera "video" setting. The Exhaust is the same setup as the BMW 135i AFE
cat back Exhaust.
Supersprint Exhaust Interior of BMW 330i
Some clips for anyone who want to hear what a Supersprint Exhaust sounds like in normal driving situations
with some play mixed in too!
To be honest there is a minor bit of drone at low RPMs under load. Once a
downshift is done to put RPMs around 3,000 under load (uphill) then the
slight drone disappears.
Review: 2005 BMW 330Ci ZHP
I review the 2005 BMW 330Ci ZHP. These are great cars, all of the M3
suspension compenents without the M3 engine, these cars are a lot of fun!
What do you think about this car? Would you rather have this or an M3?
Song is "Warm Up Suit" by Broke For Free and is used under a Creative
Commons Attribution License. The song can be found here:
"Like" the Facebook page for more updates! http://facebook.com/subaruwrxfan
2004 BMW 330ci muffler delete
Here I have my 04 BMW 330ci with a muffler delete done locally, by a
muffler shop I trusted, and replaced with two straight pipes. It is a cold
start and it sounds a little gargly to begin with, but tones down later on.
It's a cheap thing to do if you're looking for a deeper inline 6 sound.
BMW E46 330CI Schmiedmann Competition
This shows the BMW E46 330CI Schmiedmann Competition with ESS compressor
See more about the build here
All parts mounted on the BMW can be found here http://www.schmiedmann.com
BMW Quad Exhaust +Many Upgrades
2003 bmw 330i with custom quad Exhaust
originally planned on running the m3 muffler,
but my body shop guy couldn't do it
so now it is just straight pipes as you can see
also since this is a "part two"
the mods in this video are as follows:
custom painted vented hood
m3 style mirrors
painted the front lip
csl custom cf trunk lid
led tail lights
acs roof spoiler
custom quad Exhaust
replica m3 rear bumper
painted engine bay soon to be changed
suede interior and all of interior soon to be changed
part thee coming in summer!
How to Change a Wheel Bearing (long and detailed version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
**If the video helped, please give it a "thumbs up" and consider
Leave any questions or comments below and I will answer them as well.**
My Facebook: https://www.facebook.com/chrisfix8
My Twitter: https://twitter.com/ChrisFix6
Here are some other similar how to videos (there are a lot more than this):
How to change brake pads:
How to replace drum brakes:
How to change an Alternator:
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.
BMW 330ci Magnaflow Exhaust
Me revving my e46 2001 BMW 330ci with Magnaflow Exhaust. 2.25" piping, both resonators removed,
magnaflow x-pipe, and 14" dual in dual out magnaflow muffler. An aggressive
sound that maintains that silky smooth BMW straight 6 note, unlike other Exhausts that sound too raspy or
4-banger-ish. Sorry about the camera noise vibration. There is slight cabin
drone around 2200rpm. If anyone knows of any remedies, feel free to let me