Parts Search: If you like this part use the Google +1 button:

---

Price: $2,429

This item has been shown 293 times.

Click HERE for more information about this part.

Your browser does not support JavaScript. To view this page, enable JavaScript if it is disabled or upgrade your browser.
Click Here. Double your traffic. Get Vendio Gallery - Now FREE!

This listing is for a new MSD Ignition Atomic EFI System (part # 2900). This is the 525 HP system. Get a FREE MSD Digital 6A Ignition Control Box with this purchase! A $189.99 value!WE ARE OFFERING FREE UPS GROUND SHIPPING WITHIN THE CONTINENTAL USA!

This is the complete kit for anyone planning to convert from a carburetor to Atomic EFI. You get the Throttle Body, Power Module (with Wide Band O2 sensor), Handheld Controller, and the Standard Fuel Kit for up to 525hp (at the crank).

Included in this MSD Atomic EFI System:

Throttle Body

The crown jewel of the Atomic EFI system is of course the throttle body itself. Our Engineers have countless hours in designing the unit with great performance and appearance. the compact design is similar in size to a carburetor, yet contains an Electronic Control Unit, four injectors, the Idle Air Control solenoid, TPS, MAP, Intake Air Temperature (IAT) and more. It's easy to overlook all of the details so let's have a closer look-

Power Module

The Power Module is a remote mounted item for the Atomic that handles all the high current loads. MSD’s CAN-Bus technology allows for a single, clean connection between this unit and the throttle body mounted ECU.

• CAN-Bus
  These two ports are for MSD’s CAN-Bus technology. Just plug in the throttle body and the handheld controller and you are ready to go – nothing complicated! Best of all, these two ports are interchangeable, so don’t worry about which plug goes where.
• Wiring
  Most of the wiring for the Atomic comes through this loom. This includes the Fuel Pump power (no relay required!), two fan controls, Wide Band 02 sensor, 12 volt switched, and power and ground.
• Mounting
  The Power Module for Atomic can be mounted almost anywhere you like. Of course, we’d love to see you put it front and center on the fire wall, but if you would rather have it tucked out of sight that works too. Just make sure it protected from much water and has a little air flow.

Handheld Controller

This little device is how you communicate with the Atomic. The initial setup takes about 5 minutes to ask a few basic questions about your engine. After that, the handheld serves as a dash for you to see all that is happening in your engine!

• Use
  MSD knows the Handheld must be easy to use. This wasn’t made for a rocket scientist or a software engineer, the handheld is in plain English for the car enthusiasts that will use it. In the Initial Setup, you’ll answer six questions about your engine like Cubic Inches, Number of Cylinders, and your desired rev limit.
• Dash
  After the Setup is complete, you may think the Handheld is useless; not so! The Dash function of this device can serve you any time you want to know what’s happening in the engine. From exact Air Fuel Ratio readouts to Engine Coolant Temp, this set up tells you everything you want to know about your engine.
• Data and Diagnostics
  The data Atomic gathers doesn’t just disappear after you look at it on the dash. If ever an issue arises, the Diagnostics feature will display alerts and save them for up to ten starts to let you come back and see what is going on.
  

Standard Fuel Kit

MSD’s standard fuel kit is kept simple thanks to Atomic’s built in fuel rails and returnless design – less hardware to put together and less fuel line to run. All you need for this kit is included – PWM Fuel Pump (MSD PN-2225), Post Filter, 15 feet of 3/8 I.D. fuel line, mounting brackets and EFI specific fuel line clamps. All of this is designed to work with your vehicle’s existing sending unit in the gas tank so there is no need to mess with your tank at all.

Here's a basic wiring diagram of it all:

You not only get all this, but a FREE MSD Digital 6A Ignition Control Box! Part # 6201.

MSD started with a clean slate and drew up plans for an all new housing. They kept the same footprint as the traditional 6AL but lowered the profile for a sleek look. The wiring is all routed out one end of the unit through a sealed and locking connector. This eases installation and keeps your wiring looking neat and clean.

Inside the Digital 6A you’ll find a microprocessor that monitors and controls every firing. The circuits are updated with efficient components that help the ignition produce more power while drawing less current! In fact, the new Digital 6A deliver over 530 volts to the coil with up to 135mJ of spark energy – for every firing! Increased output combined with MSD’s proven multiple spark series is a win-win situation!

The new Digital 6A is supplied with the wiring harness and the components you’ll need for installation. The ignitions are compatible on 4, 6 or 8-cylinder engines with 12-volt, negative ground electrical systems. They’ll accept trigger inputs from breaker points, amplifiers and magnetic pickups.

Payment: We accept Paypal as payment. You can also call in a credit card payment over the phone toll free at 1-800-846-4252 Ext. 319. Ask for Andrew. We accept VISA, MasterCard, Discover and American Express.

Shipping: Shipping will be FREE via UPS Ground within the continental USA. UPS cannot ship to PO and APO Boxes. A tracking number will be provided once your item(s) ships. We can only ship to the confirmed address of Paypal payments. A signature will be required upon delivery for all orders of $250 and above. Local customers are always welcome to stop in and inspect the items before purchase, and/or to pick the item up. There will be no handling or shipping charges for local pick-up customers. NY State sales tax will apply.

Returns: We accept returns from 14 days after you receive your item(s). Returned items must be sealed and/or in "as-sold" and resaleable condition. Buyer pays for return shipping charges. Please call us to obtain an RGA number before shipping any merchandise back to us. If for any reason you are not 100% satisfied with your purchase from us, please don't hesitate to contact us either through 's messaging system or call us toll free at 1-800-846-4252 Ext. 319. We will be glad to assist you with any problems you may be experiencing, or to facilitate a return. Your browser does not support JavaScript. To view this page, enable JavaScript if it is disabled or upgrade your browser.

Posted with Mobile

On Nov-16-12 at 14:19:02 PST, seller added the following information:

FREE! Sellers: Add a FREE map to your listings. FREE!