When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $36.45
I Pledge allegiance to the flag,America,God,Country,Molon Labe,USA,
SIZE IS Approx. 30"x14" If you need a different size please ask.
Leave your color choice in the sellers notes,thank you.
Color will beWHITEunless specified.
PatriotFitGear.com
Decal is VinylCut so it will be one single color, but is available in
WHITE,BLACK,ROYAL BLUE, PINK, RED, HUNTERS ORANGE, NEON GREEN, DARK GREEN,GOLD, and SILVER.
Please specifycolor..
The vinyl is3MIL, resistant to Sun, Rain, Snow & Sleet.The decal will stick toany hard, smooth surface and are suitable for wet locations (Boat, Car, CarWindow, Laptop, Instrument Cases, Snowboard Decks, School Lockers, Mirrors,etc.)
An application (transfertape) overlay allows for precise and easy placement.
All decals arecomputer cut and are customizable.
HOW TO APPLY
STEP 1: CLEAN THAT AREA GOOD!
First make sure youhave a dry place and no wind to install your decal.
Make sure to prep thearea, this is the most important part of installing a decal! If you putyour decal or sticker on a dirty surface, it will just pick that dirt and grimeup like a lint roller does your shirt, those aren't so sticky after you usethem are they! So let’s make sure the area is nice and clean so that itcan adhere to where you are going to place it.
You can use soap and water, rubbing alcohol, or any other fast dryingcleaner. My favorite is rubbing alcohol since it dries by itself withinseconds and leaves no residue behind. On that note, do NOT use anythinglike Windex or other household spray cleaners that leave a residue behind oroily substance, that defeats the purpose and will cause your decal/sticker notto adhere to the best of it capabilities.
STEP 2: DECIDE AND PEEL!
After you have cleanedyour car, you now need to decide where you want to center your decal in thearea you cleaned. I use a measuring tape to measure from different spotson the car tomake sure I have it exactly where I want it and that it willnot turn out crooked. When I measure I use a piece of masking tape tomark the measurements, normally four for left/right/top/bottom. Then Ihave a somewhat boxed area to force me to place the decal where it should go.
Be aware after you stick it, you might cannot undo itand use it again, since it can separate the design or text from each other.After you decide where you want it, go ahead and start to peel your decal back,if it doesn't stick to the transfer tape the first pull, replace the transfertape and push it together with your fingers or use a credit card to presstogether.
STEP 3: PLACE THAT DECAL!
So you cleaned yourarea and also decided how and where you are going to place your new decal orsticker and you made sure your decal can peel apart easily.
FOR SMALLER DECALS -
Now fully peel thedecal off the backing and hold it on the tips of the masking/transfertape. Try not to touch the back of the decal itself since it could leavedirt on your decals back side.
You should have each hand holding the furthest corners from each other and keepit tight so that the decal does not fold in on itself. Place one end ofthe decal down and then smooth it out to the other end till the decal is fullyplaced.
FOR BIGGER DECALS -
Do not fully removethe backing on your decal. You will want to remove about 1/3 of thebacking and start by applying that 1/3 of the decal to the car. Thenslowly pull more of the backing off while at the same time apply the decal tothe car until you have fully installed the decal. Either work left toright or right to left, which ever you feel best doing.
Don't forget you can always buy a $1 spray bottle at your dollar store, put ONEsmall drop of soap in it and fill with water and shake. Then LIGHTLY (IMEAN LIGHTLY)spray the area and then apply the decal. This is onlysuggest for bigger decals or decals that you need to be in a precise area.
STEP 3: THE HARDESTPART!
Waiting... yes this isthe hardest part, because most people are so impatient that they can't wait andthey mess up the decal by removing the transfer tape too early!
The best way to allow your decal to dry is out in the sun, having it in theshade or in a cool place will only make it take longer. If you used amist of soapy water when installing your decal and do not let the sun dry it,then it will take a very long time before it adheres correctly, since nothingis there to remove the water and dry the decal to the surface.
Do not try and rush this buy using a heat gun, you can melt the transfer tapeand vinyl and when you peel it, it could cause the decal to stretch with thetransfer tape. Again the best way is the sun. Finally just give the decal30 minutes before you remove the transfer tape, go inside and eat lunch.By the time you’re done you should be able to go back outside and finish yourdecal and be in a good mood from that great lunch and nice cold sweettea! If your decal is still not sticking, make sure you got it in the sunand it is warm outside, and just give it a bit longer.
After ~30 minutes todry, remove transfer paper.