When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $5.99
Stock # 21
This itemis pre-owned – it will work like new once programmed to your vehicle
One (1)
O.E.M. OriginalEquipment Manufacturer Factory
remote keyless entry fob alarm
Transmitter controlclicker keyfob controller replacement
Functionsat 100% Tested & Guaranteed
Item #: 21 FCC ID: ABO0303T AB00303T ABOO303T, ABO 0303T
ABO0302T, AB00302T, ABOo302T, ABO 0302T Part #: 25602667, 68, 69 256026676869 Canada/Mexico Part #: 1551 102 818, 1551102818, 218 K103, 218K103
Remote / Battery Specifications
Condition:
Pre-Owned
Battery:
Yes, Installed
Buttons:
3: Lock, Unlock, Trunk Release
Required Batteries:
2: CR2016
Frequency:
315MHz (315 MHz)
Compatible Vehicles*:
1991 1992 1993 Buick Century
1992 1993 1994 1995 Buick LeSabre
1989 1990 1991 1992 1993 1994 1995 Buick Park Avenue
1993 1994 1995 Buick Riviera
1995 Oldsmobile Aurora
1990 1991 1992 Oldsmobile Cutlass, Cutlass Supreme
1991 1992 1993 1994 1995 Oldsmobile Eighty-Eight 88, Ninety-Eight 98
1990 1991 1992 Oldsmobile Toronado
1991 1992 1993 1994 1995 Pontiac Bonneville
*All vehicles with factory installed Remote Keyless Entry (RKE).
Buick Park Avenue Ave
PROGRAMMING INSTRUCTIONS
1989-1991
the manufacturer’s programming instructions for your vehicle make model and year specify diagnostic programming required
You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment
PROGRAMMING INSTRUCTIONS 1992-1993
DATA LINK CONNECTOR
1. Locate the Data Link Connector (DLC) underneath the driver\'s side dashboard.
Use the figure asa map for your DL (They are not lettered on your vehicle.)
The view is looking straight into thecavitiesof the DLC.
2. Connect cavity G withcavity Ausing a fused jumper wire.
Your vehicle will respond by locking and unlocking the door locks within 2 seconds.
3. Press any button on first remote to be programmed.
Locks will lock and unlock verifying remote wasprogrammed.
4. Press any button on second remote to be programmed if applicable.
Locks will lock and unlock to verifyremote was programmed.
5.Remove jumper wire and test remote(s)
PROGRAMMING INSTRUCTIONS 1994-1995
1. Insert key in ignition and leave in the OFF position
2. Locate theData Link Port. It is locatedunder dash driver’s side. Be sure you know which pins are 8 and 4.
(Note port is wider at top) YourOBDII port will nothave numbers, use this diagramfor reference.
3. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with asuitablejumper wire (leave the jumper wireconnected throughout the programming procedure). Makesure you know which terminals are 8 and 4.
4. Close doors.
5. Turn ignition to the ON position (asfar as you can go without cranking the engine).Doors will lock.
6. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to beprogrammed. After about 15 seconds, the vehiclewill respond by locking and unlocking the doors.Release the buttons on the transmitter.
7. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
8. Remove jumper wire applied to the OBDII Port.
9. A maximum of two keyless remotes can be programmed.
Buick Riviera
PROGRAMMING INSTRUCTIONS
The manufacturer’s programming instructions for your vehicle make model and year specify diagnostic programming required
You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment
Buick LeSabre Le Sabre
PROGRAMMING INSTRUCTIONS 1992-1993
DATA LINK CONNECTOR
1. Locate the Data Link Connector (DLC) underneath the driver\'s side dashboard.
Use the figure asa map for your DL ( They are not lettered on your vehicle.)
The view is looking straight into thecavitiesof the DLC.
2. Connect cavity G withcavity Ausing a fused jumper wire.
Your vehicle will respond by locking and unlocking the door locks within 2 seconds.
3. Press any button on first remote to be programmed.
Locks will lock and unlock verifying remote wasprogrammed.
4. Press any button on second remote to be programmed if applicable.
Locks will lock and unlock to verifyremote was programmed.
5.Remove jumper wire and test remote(s)
PROGRAMMING INSTRUCTIONS 1994-1995
1. Insert key in ignition and leave in the OFF position
2. Locate theData Link Port. It is locatedunder dash drivers side. Be sure you know which pins are 8 and 4.
(Note port is wider at top) YourOBDII port will not have numbers, use this diagramfor reference.
3. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitablejumper wire (leave the jumper wireconnected throughout the programming procedure). Makesure you know which terminals are 8 and 4.
4. Close doors.
5. Turn ignition to the ON position (asfar as you can go without cranking the engine).Doors will lock.
6. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to beprogrammed. After about 15 seconds, the vehiclewill respond by locking and unlocking the doors.Release the buttons on the transmitter.
7. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
8. Remove jumper wire applied to th OBDII Port.
9. A maximum of two keyless remotes can be programmed.
Buick Century
PROGRAMMING INSTRUCTIONS
1991 - 1992
the manufacturer’s programming instructions for your vehicle make model and year specify diagnostic programming required
You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment
PROGRAMMING INSTRUCTIONS 1993
1.Locate the greenprogramming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has wires leading up to it and it is not connected to anything.)
2. Jump programming connector terminals.
3. System should now lock and unlock doors and trunk lid to indicateprogrammingmode has been entered. Trunk lid must have activated before proceeding.
4. Press any button on keyless remote once.
System should now lock and unlock doors and trunk lid, indicatingsuccessfulprogramming of keyless remote. Trunk lid must have activated before proceeding.
5. Repeat step 4 for additional remote or other existing keyless remote.
NOTE:A maximum of only two Keyless Remotes can be programmed.
6. Remove programming connector jumper wire to exit programming mode.
7. Test remote(s).
How to find out if this remote iscompatible with your Vehicles’ installed RKE System
If you\'renotsure your vehicle can use this remote, please ask questions or contactyour local dealer first.
1. Check the back of yourcurrent or old keyless remote to match FCC ID /Part #’s.
2. Contact your localdealer and tell them your VIN# and ask what part # / FCC ID you need.
Yourvehicle will be installed with one of the following keyless entry systems:
a. Standard Keyless RemotePackages: Installed at time of manufacture.
b.Optional Keyless Remote Packages: Installed by a dealer.
c. Aftermarket Keyless Remote Packages:Installed by previous owner or a car/audio shop.
d.No remote keyless entry system at all.
Theabove information can change which remote you need
for your installed remote keyless system.
AustralianCustomers: The frequency of our remotes typically do notmatch the frequency needed for Australian Model Remotes. Please verify thatthis remote will work for your vehicle prior to purchase.
Payment: We acceptpayment via PayPal or Credit Card. Please contact us via eBay messages for anyquestions concerning payments. Payment is expected within 5 days
PASALES TAX: As per the State of PA Franchise Board we mustcollect sales tax from PA Residents for any purchase made from our store.
Contact/Email: Due to scams etc,we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages& Best Offers are checked throughout the day & we typically respond 7days a week. Please contact us with questions via eBay messages (keyless4u).
100% Guarantee RemoteShipping / Return Policy
Warranty/Returns:
1.Wehave a 30 day return policy.
2.Allreturns for replacements and refund need an RMA #.
3.Pleasecontact us before returning items so we can give you theRMA # and theproper return address.
4.Norefunds / replacements will be granted without an RMA#
5.Allreturns with CUT key will incur a $20 deduction from the refund.
We ensure properworking condition of all previously used or new remotes through a serious oftests performed with the Santronics Testing device. Each button is tested forfunctionality prior to shipment and then logged.
PleaseNote:Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection toverify originality of remote sent prior to refund or replacement.
Does this keyless remote entry come with a battery?
Yes. It will have a working battery installed.
Battery Condition:
A. All remotes sold on Keyless4u include working batteries.
B.Installed batteries are not tested forbattery life- they are simply working.
Some are new and some are used.
WORDKEY:
- Keyless Remote Entry = Vehicle Lock / Unlock Remote Control
- RKE = Remote Keyless Entry
- Keyfob or Key Fob = Keyless Remote Transmitter Control
- Clicker = Keyless Remote Entry Control
- VIN # = Vehicle Identification #: 17 characters
- OEM = Original Equipment Manufacturer
.
.
.
.