Black CarLashes (r) 3D Headlight Eyelashes Accessories 3D for Mitsubishi for Sale


When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Price: $26.99

Classic Black Car Lashes™ - Giant Eyelashes design for: ALL Mitsubishi vehicleNote: Does not include the eyeliner

CLASSICCar Lashes™ - Giant Eyelashes for Your Car
You are now entering the formerly forbidden "Man-Zone" of car accessories. Move over mud flaps and racing stripes and say hello to eyelashes for your car! CarLashes® turn the daily drab of driving into a fun and fashionable, feel-good (even emotional) adventure.

Since exploding online in 2010, CarLashes® have gone from a girly trend to a diva necessity. After all, ladies have serious purchasing power. Women buy more than half of the new cars in the U.S. and influence up to 85 percent of all car purchases. Sure, women may seek a practical ride that fits their needs and lifestyle, but they also crave a little bling … and a lot of fun.Lovely ladies across the globe have lashed up to join the Miles of Smiles Movement to shatter the myth that car accessories are just for men. The Miles of Smiles Movement is all about feeling great inside and out and spreading some love along the way.

Press CarLashes was featured on CNN on September 7, 2010.



Lash Attachment Instructions
Overview
                  1. Determine Placement
                  2. Clean Surface
                  3. Practice
                  4. Attach Tape To Lash*
                  5. Attach Lash To Car

DETAILSThe lash needs to be attached to a clean smooth surface on the vehicle.
All of the tape should be touching the surface where the lash is attached.

PLACEMENT:
Try the top surface of the headlight glass. You will probably have to open thehood to access this surface. If it is smooth and has no rubber trim this should work nicely. Ifthere is rubber trim, sometimes you can slide the lash between the trim and the headlight.


PLACEMENT:
If the top of the headlight is not flat or has rubber trim, try the bottom surface of the hood edge above the headlight. Since this surface may be slightly irregular, press firmly to help the foam tape conform to the underside surface of the hood. Leave the hood open for several hours or over night before closing to insure complete bonding.

If the underside of the hood is too irregular, try the top surface of the hood edge above the headlight. You can also apply the lash to the top edge of the headlight, bending the lashes up if necessary to clear the headlight beam.

* Depending on lash style tape may already be applied to lash on the correct side.

PLACEMENT IF YOUR HEADLIGHTS ARE ROUND OR OVAL
Apply the lashes to the surface next to the headlight glass. The lash can also be applied directly to the headlight glass if it does not interfere with the function of the light.
Curve the base of the lash to follow the edge of the headlight. Make sure to apply enough force to keep bending the lash around the edge of the headlight. Each individual lash can be adjusted up and away from the headlight after the lash is attached with the 3M tape. Press down with your thumb as shown and firmly bend the lash up.

If your headlights are not located under the hood, the lashes can be attached just above the headlight, or on the top edge of the headlight glass. See if there is a gap along the top edge of the headlight that lash can be slipped into-pull out the red backing after the lash is slipped into the crack. Use a table or butter knife to press the lash down firmly in the crack.

Bend up the lashes at the base as needed to keep them from interfering with the headlight. If the lash is too wide for the headlight, you can trim off any overhanging lashes with scissors. The tips of the lashes can also be trimmed to make them shorter.

APPLY THE TAPE TO THE LASH FIRST:
Remove a small portion of the protective backing from one side of the tape—leave the protective backing on the other side of the tape in place. Start at one end and and press the tape along the base of the lash. Keep the edge of the tape exactly along the bottom edge of the base of the lash. Make sure to apply the tape to the correct side of the lash for the location on the vehicle you have chosen. For example, on the bottom of the lash when applying to the top of the headlight glass.

CLEAN:
Make sure the surface is clean and dry before attaching. Use the enclosed Alcohol Prep Pad to remove any dirt, grease, or car wax. Wipe both the lash and the vehicle surface with the Prep Pad and allow to dry.

Practice before attaching! The 3M double sided trim tape is VERY STICKY! It cannot bere-positioned. Once it touches a surface it is very difficult to remove without messing up the tape. Once the lash is applied, rub firmly along the length of the lash with your thumb to make sure the tape is completely attached.

NOTE:
You can cut the lashes apart into individual lashes with scissors and apply them one at a time. Apply the 3M tape before cutting apart. This may provide more options for creatively attaching the lashes. For example, individual lashes can be spaced farther apart and pointed in different directions to create fan effects.

IMPORTANT

  1. Make sure the tips of the lashes are not flexing back and touching the car at high speed--bend the lashes down or trim them shorter with scissors to avoid this.
  2. Traveling at excessive speed may cause the lashes to start peeling up. If this happens, remove them immediately and re-apply with fresh 3M tape.
  3. Best if applied above 50 degrees and in shade.
  4. Avoid getting wet or driving at high speed for 24 hours.

OPTIONAL CRYSTAL EYELINER

  1. Remove a portion of the red protective cover from one end of the Crystal Eyeliner. The crystal eyeliner is long enough for one crystal to overhang the lash at each end. You can trim off crystals to the desired length using scissors.
  2. Starting at the outside end of the lash, apply the liner to the edge of the painted surface above the lash or directly on top of the lash if the base is exposed.
  3. Work your way along pulling off only a short portion of the protective backing and pressing the crystals down one or two at a time.
    NOTE:
    The 3M tape stretches-do not pull on the strip of crystals as they are applied since this will open up a gap in the spacing between the crystals. Just twist them to bend along the edge of the lash as you press them down in place.
  4. Remove the red protective cover bit by bit as you work your way along.
  5. If you apply more than one row of crystals you can stretch the tape slightly to align the crystal rows one next to the other as you apply the second row.
Trademark CarLashes® owned by Robert A. SmallCarLashes® copyright 2009-2015 Robert A. SmallPATENTED


Parts Search:


Follow